Related Experiment Video

Updated: Sep 5, 2025

Knowledge Based Cloud FE Simulation of Sheet Metal Forming Processes
11:05

Knowledge Based Cloud FE Simulation of Sheet Metal Forming Processes

Published on: December 13, 2016

12.3K

Efficient Model of the Interaction of Elastomeric Filler with an Open Shell and a Chrome-Plated Shaft in a Dry

Maciej Dutkiewicz1, Andrii Velychkovych2, Ivan Shatskyi3

  • 1Faculty of Civil and Environmental Engineering and Architecture, Bydgoszcz University of Science and Technology, Kaliskiego 7, 85-796 Bydgoszcz, Poland.

Materials (Basel, Switzerland)
|July 9, 2022
PubMed

Keywords:
chrome-plated shaftcoefficient of frictiondampingelastomeric filleropen shell

More Related Videos

In Situ High Pressure Hydrogen Tribological Testing of Common Polymer Materials Used in the Hydrogen Delivery Infrastructure10:01

In Situ High Pressure Hydrogen Tribological Testing of Common Polymer Materials Used in the Hydrogen Delivery Infrastructure

Published on: March 31, 2018

7.7K
Atomic Force Microscopy Cantilever-Based Nanoindentation: Mechanical Property Measurements at the Nanoscale in Air and Fluid08:58

Atomic Force Microscopy Cantilever-Based Nanoindentation: Mechanical Property Measurements at the Nanoscale in Air and Fluid

Published on: December 2, 2022

3.2K

Related Concept Videos

Design Example: Deciding Thickness of Lubricating Fluid in a Shaft01:23

Design Example: Deciding Thickness of Lubricating Fluid in a Shaft

Effective lubrication between a rotating shaft and its bearing housing is essential in rotating machinery to minimize friction, wear, and energy loss. With carefully controlled thickness and viscosity, the lubricant layer prevents metal-to-metal contact, ensuring smooth operation.
To calculate the required thickness of the lubricant layer, the tangential velocity at the shaft's surface must first be determined. This velocity is calculated by converting the rotational speed to angular...
153
Circular Shafts - Elastoplastic Materials01:24

Circular Shafts - Elastoplastic Materials

The study of solid circular shafts under stress shows that within the elastic limit, stress increases directly to the distance from the shaft's center. This relationship holds until the shaft reaches a critical point of stress, beyond which it begins to yield, marking the transition from elastic to plastic deformation. At this crucial juncture, the maximum torque the shaft can endure without permanent deformation is determined, signifying the limit of its elastic behavior.
As torque on the...
152
Stress Concentrations in Circular Shafts01:18

Stress Concentrations in Circular Shafts

Consider the elastic torsion formula, which applies to a circular shaft with a consistent cross-section. This formula assumes that the shaft's ends are loaded with rigid plates firmly attached. However, in many cases, torques are applied to the shaft through mechanisms like flange couplings or gears, which are connected by keys inserted into keyways. This application method modifies the stress distribution near the point of torque application, causing it to deviate from the distributions...
232
Dry Friction01:30

Dry Friction

Dry friction occurs between two solid surfaces in contact as they attempt to move relative to one another. In daily life, dry friction is encountered in various forms, such as when walking on the ground, sliding an object across a table, or rubbing hands together. Despite its ubiquity, the underlying mechanisms behind dry friction are not readily visible.
To illustrate this concept, imagine a wooden crate resting on a rough, non-uniform horizontal surface. When an external force is applied to...
462
Characteristics of Dry Friction01:21

Characteristics of Dry Friction

Dry friction occurs when two solid surfaces slide against each other without any lubrication or fluid present. It causes resistance when pushing objects along a surface, like a gardener pushing a wheelbarrow. The force applied to move the cart causes dry friction between the wheel and the ground.
Before the wheelbarrow starts moving, the static frictional force acts tangentially to the contact surface, opposing the force that is about to induce the motion. This frictional force prevents the...
672
Residual Stresses in Circular Shafts01:10

Residual Stresses in Circular Shafts

In materials that exhibit elastic and plastic behavior, known as elastoplastic materials, residual stresses can accumulate when these materials experience plastic deformation. This deformation arises from either high levels of shearing stress or significant strains. Residual stresses are internal stresses that persist within a material after removing the external force causing deformation. This phenomenon is demonstrated when observing the behavior of a shaft under torque; notably, the...
228