Related Experiment Video

Updated: Sep 4, 2025

Angle-resolved Photoemission Spectroscopy At Ultra-low Temperatures
08:53

Angle-resolved Photoemission Spectroscopy At Ultra-low Temperatures

Published on: October 9, 2012

17.7K

Elastocaloric determination of the phase diagram of Sr2RuO4

You-Sheng Li1, Markus Garst2,3, Jörg Schmalian3,4

  • 1Max Planck Institute for Chemical Physics of Solids, Dresden, Germany.

Nature
|July 13, 2022
PubMed

More Related Videos

Synthesis of Non-uniformly Pr-doped SrTiO3 Ceramics and Their Thermoelectric Properties11:07

Synthesis of Non-uniformly Pr-doped SrTiO3 Ceramics and Their Thermoelectric Properties

Published on: August 15, 2015

10.0K
Atomically Defined Templates for Epitaxial Growth of Complex Oxide Thin Films08:49

Atomically Defined Templates for Epitaxial Growth of Complex Oxide Thin Films

Published on: December 4, 2014

14.4K

Related Concept Videos

Phase Diagram01:19

Phase Diagram

The phase of a given substance depends on the pressure and temperature. Thus, plots of pressure versus temperature showing the phase in each region provide considerable insights into the thermal properties of substances. Such plots are known as phase diagrams. For instance, in the phase diagram for water (Figure 1), the solid curve boundaries between the phases indicate phase transitions (i.e., temperatures and pressures at which the phases coexist).
6.0K
Phase Diagrams02:39

Phase Diagrams

A phase diagram combines plots of pressure versus temperature for the liquid-gas, solid-liquid, and solid-gas phase-transition equilibria of a substance. These diagrams indicate the physical states that exist under specific conditions of pressure and temperature and also provide the pressure dependence of the phase-transition temperatures (melting points, sublimation points, boiling points). Regions or areas labeled solid, liquid, and gas represent single phases, while lines or curves represent...
43.3K
Phase Transitions: Melting and Freezing02:39

Phase Transitions: Melting and Freezing

Heating a crystalline solid increases the average energy of its atoms, molecules, or ions, and the solid gets hotter. At some point, the added energy becomes large enough to partially overcome the forces holding the molecules or ions of the solid in their fixed positions, and the solid begins the process of transitioning to the liquid state or melting. At this point, the temperature of the solid stops rising, despite the continual input of heat, and it remains constant until all of the solid is...
12.8K
Recrystallization: Solid–Solution Equilibria01:10

Recrystallization: Solid–Solution Equilibria

Recrystallization is a purification technique used to separate impurities from solid compounds. In this technique, no chemical reactions occur. Instead, it exploits physical properties only, specifically, the solubility differences between the desired compound and impurities, either at a single temperature or at different temperatures, and under other selected conditions. The solid-solution equilibrium (solubility equilibrium) of each component in the solution represents a binary phase...
1.2K
Phase Changes01:19

Phase Changes

Phase transitions play an important theoretical and practical role in the study of heat flow. In melting or fusion, a solid turns into a liquid; the opposite process is freezing. In evaporation, a liquid turns into a gas; the opposite process is condensation.
A substance melts or freezes at a temperature called its melting point and boils or condenses at its boiling point. These temperatures depend on pressure. High pressure favors the denser form of the substance, so typically, high pressure...
4.5K
States of Matter and Phase Changes00:59

States of Matter and Phase Changes

The internal energy of a substance—the total kinetic energy of all its molecules and the potential energy of their associated forces—depends on the strength of the intermolecular forces in the condensed phases and the pressure exerted on the substance. The internal energy of a substance is the highest in the gaseous state, the lowest in the solid state, and intermediate in the liquid state. Phase transitions are caused by changes in physical conditions, such as temperature and...
1.2K