Related Experiment Video

Updated: Sep 3, 2025

Laboratory and Field Protocol for Estimating Sheet Erosion Rates from Dendrogeomorphology
07:20

Laboratory and Field Protocol for Estimating Sheet Erosion Rates from Dendrogeomorphology

Published on: January 7, 2019

7.8K

Lack of Correlation between Landscape Geometry and Transition Rates

Wen Jia1,2, Atchuta Srinivas Duddu3, Mohit Kumar Jolly3

  • 1Center for Theoretical Biological Physics, Northeastern University, Boston, Massachusetts 02115, United States.

The Journal of Physical Chemistry. B
|July 25, 2022
PubMed

More Related Videos

Use of Principal Components for Scaling Up Topographic Models to Map Soil Redistribution and Soil Organic Carbon09:44

Use of Principal Components for Scaling Up Topographic Models to Map Soil Redistribution and Soil Organic Carbon

Published on: October 16, 2018

10.3K
Measuring and Mapping Patterns of Soil Erosion and Deposition Related to Soil Carbonate Concentrations Under Agricultural Management08:09

Measuring and Mapping Patterns of Soil Erosion and Deposition Related to Soil Carbonate Concentrations Under Agricultural Management

Published on: September 12, 2017

11.9K

Related Concept Videos

Methods of Obtaining Topography01:25

Methods of Obtaining Topography

Topography involves measuring and mapping land elevations, natural features, and artificial structures to create accurate representations of the terrain. Topographic surveying relies on traditional and modern methods, each with distinct advantages and limitations.Traditional Surveying Methods:Transit stadia surveys and plane table surveys were widely used traditional surveying methods. These techniques relied on instruments like theodolites and stadia rods for measuring distances and angles,...
108
Design Example: Maintaining Level of an Embankment01:19

Design Example: Maintaining Level of an Embankment

Constructing a roadway embankment over uneven terrain requires precise leveling to ensure stability and proper drainage. Surveyors use a leveling instrument and staff to calculate ground elevations and determine the required fill material at each point along the embankment alignment.The process begins by positioning a leveling instrument near a benchmark with a known elevation. A backsight reading establishes the instrument height, which serves as a reference for subsequent measurements. A...
119
Boundary Conditions: Lossless Lines01:21

Boundary Conditions: Lossless Lines

Consider a single-phase, two-wire, lossless transmission line terminated by an impedance at the receiving end and a source with Thevenin voltage and impedance at the sending end. The line, with length, has a surge impedance and wave velocity determined by the line's inductance and capacitance.
At the receiving end, the boundary condition states that the voltage equals the product of the receiving-end impedance and current. This relationship is expressed as a function of the incident and...
148
Energy Line and Hydraulic Gradient Line01:27

Energy Line and Hydraulic Gradient Line

Based on Bernoulli's equation, the energy line (EL) and hydraulic grade line (HGL) provide graphical representations of energy distribution in a fluid flow system. For steady, incompressible, inviscid flows, Bernoulli's equation is expressed as:
1.3K
Plotting of Topographic Maps01:29

Plotting of Topographic Maps

Topographic maps represent the Earth's surface features using contour lines, which connect points of equal elevation to create a two-dimensional representation of three-dimensional terrain. Creating a topographic map requires a systematic approach.Begin by plotting a scaled grid and marking intersections corresponding to the survey's elevation data points. Assign elevation values at these intersections to build the base map. Next, determine contour levels using a consistent contour interval,...
100
Transition Zone01:28

Transition Zone

The transition zone in concrete is a critical area where aggregate meets cement paste, marked by a distinct porosity and weakness compared to the surrounding material. The adhesion around the aggregates is primarily due to Van Der Waals forces. The voids within this zone influence its robustness; initially, it is less durable than the surrounding bulk mortar due to larger voids. Initially, when concrete is compacted, a higher water-cement ratio near the aggregates leads to the formation of...
143