Related Experiment Video
Updated: Aug 30, 2025

Biofilm Removal Using Carbon Dioxide Aerosols without Nitrogen Purge
Published on: November 6, 2016
Effect of Sodium Hypochlorite in Dental Unit Waterline on Aerosolized Bacteria Generated from Endodontic Procedures
Ahmad Rayyan1, Amber Ather2, Kenneth M Hargreaves1
1Department of Endodontics, University of Texas Health Science Center at San Antonio, San Antonio, Texas.
Introduction:
Aerosol generation in a dental setting is a critical concern, and approaches that aim at decreasing bacterial load in aerosols are of high priority for dental professionals. The objectives of this study were to evaluate the relative effect of various endodontic procedures on the generation and dissemination of aerosols and the effect of 0.1% sodium hypochlorite (NaOCl) in dental unit waterlines (DUWLs) on the bacterial load in the generated aerosols in a clinical setting.
Methods:
The study was completed in 2 phases. The classic passive sampling technique using brain-heart infusion agar plates was used. Agar plates were strategically placed throughout the operatory at predefined locations. In phase 1, to evaluate the effect of different endodontic procedures on the generation and dissemination of aerosols, we collected a total of 38 samples. After baseline collection, test samples were collected during vital pulp therapy (VPT) full pulpotomy (n = 10), nonsurgical root canal therapy (NSRCT, n = 10), surgical root canal therapy (SRCT, n = 10), and incision and drainage (n = 8) procedures. Bacterial growth was expressed as colony-forming units at 48 hours after sample collection. Data were analyzed using 1-way analysis of variance with the Tukey multiple comparison post hoc test. In phase 2, to evaluate the effect of 0.1% NaOCl in the DUWL on the bacterial load in the generated aerosols, a total of 30 samples were collected. All procedures including VPT (n = 10), NSRCT (n = 10), and SRCT (n = 10) were performed with 0.1% NaOCl in the DUWL. Bacterial growth was expressed as colony-forming units at 48 hours after sample collection. Data were analyzed using 2-way analysis of variance with the Tukey multiple comparison post hoc test.
Results:
All endodontic procedures generated aerosols at all tested locations, except incision and drainage. Aerosols were disseminated as far as 3 m from the patient's head with no significant difference between various locations (P > .05). VPT procedures generated the maximum number of aerosols compared with NSRCT and SRCT. Adding 0.1% NaOCl to DUWLs significantly reduced the bacterial load in the generated aerosols in all treatment groups compared with groups treated with untreated waterlines (P < .05). No significant difference was noted in the bacterial load between all groups with treated waterlines (P > .05).
Conclusions:
All tested endodontic procedures led to the generation and dissemination of contaminated aerosols, and the addition of 0.1% NaOCl as a biocide to the DUWL led to a statistically significant reduction in the bacterial load.
More Related Videos
07:07Controlled-release of Chlorine Dioxide in a Perforated Packaging System to Extend the Storage Life and Improve the Safety of Grape Tomatoes
Published on: April 7, 2017
09:02A Method to Test the Efficacy of Handwashing for the Removal of Emerging Infectious Pathogens
Published on: June 7, 2017
Related Concept Videos
Chemical Agents for Microbial Control
Hand hygiene
Hand washing...
Methods of Sterilization II: Chemical Methods
Using chemical sterilization rather than heat to clean out equipment is recommended. It eradicates and removes all bacteria,...
Suctioning the Oropharyngeal Airway
After assembling the equipment, the nurse should practice hand hygiene and don appropriate PPE according to infection control guidelines to avoid the...
Physical Methods for Controlling Microbial Growth: Radiation and Filtration
Cleaning, Sterilization, and Disinfection
Cleaning
The cleaning process usually involves using water with detergents or enzymatic cleaner and removing foreign material from objects and surfaces, including organic material such as body fluids or inorganic material like soil. Cleaning is performed before high-level disinfection and sterilization because foreign materials on the cover of the devices interfere with process...