Related Experiment Video

Updated: Aug 28, 2025

Micromechanical Tension Testing of Additively Manufactured 17-4 PH Stainless Steel Specimens
05:38

Micromechanical Tension Testing of Additively Manufactured 17-4 PH Stainless Steel Specimens

Published on: April 7, 2021

3.5K

Research on the Springback Behavior of 316LN Stainless Steel in Micro-Scale Bending Processes

Shubiao Guo1,2, Chenchen Tian1,2, Haitao Pan1,2

  • 1Key Laboratory of High Efficiency and Clean Mechanical Manufacture of Ministry of Education, School of Mechanical Engineering, Shandong University, Jinan 250061, China.

Materials (Basel, Switzerland)
|September 23, 2022
PubMed

Keywords:
constitutive modelmicro-bendingsize effectspringbackstrain gradient

More Related Videos

A Novel Biaxial Testing Apparatus for the Determination of Forming Limit under Hot Stamping Conditions07:40

A Novel Biaxial Testing Apparatus for the Determination of Forming Limit under Hot Stamping Conditions

Published on: April 4, 2017

7.7K
Generating Lap Joints Via Friction Stir Spot Welding on DP780 Steel07:18

Generating Lap Joints Via Friction Stir Spot Welding on DP780 Steel

Published on: August 13, 2019

7.1K

Related Concept Videos

Bending of Material: Problem Solving01:09

Bending of Material: Problem Solving

In this lesson, determine the ratio of the maximum bending moments applied to two metal pipes, given that both pipes can withstand a maximum stress of 100 MPa. Both pipes have an outer radius of 1.8 cm. Pipe A has an inner radius of 1.5 cm, and Pipe B has an inner radius of 1 cm. The ratio of the maximum bending moment applied to two metallic pipes, each with a different inner and outer radius, is determined by considering their dimensions. The inner radius of the first pipe is 1.5 cm, and for...
238
Plastic Behavior01:21

Plastic Behavior

A material's elastic behavior is characterized by the disappearance of stress once the load is removed, allowing the material to return to its original state. However, when stress surpasses the yield point, yielding commences, marking the onset of plastic deformation or permanent set. This change from elastic to plastic behavior is influenced by the peak stress value and the duration before the load is removed. An intriguing observation occurs when a specimen is loaded, unloaded, and...
253
Residual Stresses in Bending01:18

Residual Stresses in Bending

In the study of elastoplastic members subjected to bending moments, understanding the loading and unloading phases is crucial for assessing material behavior and structural integrity. During the loading phase, as the bending moment increases, the material initially responds elastically, adhering to Hooke's Law, where stress is directly proportional to strain. When the load exceeds the yield strength, plastic deformation occurs, resulting in permanent strain and deformation that remains even...
241
Members Made of Elastoplastic Material01:19

Members Made of Elastoplastic Material

The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
As the bending moment...
142
Bending01:10

Bending

Pure bending is a fundamental concept in structural mechanics, essential for understanding how materials deform under symmetrical loads without direct forces. Pure bending occurs when prismatic members, such as beams, are subjected to equal and opposite moments that induce bending. The phenomenon is crucial as it allows for predicting stress distributions without the influence of axial or shear forces.
In pure bending, the bending stress in a beam is calculated based on the bending moment and...
413
Stress-Strain Diagram - Ductile Materials01:24

Stress-Strain Diagram - Ductile Materials

The stress-strain relationship in ductile materials such as structural steel or aluminium is intricate and progresses through several stages. When a specimen is loaded, it initially exhibits a linear length increase, depicted by a steep straight line on the stress-strain diagram. It indicates the material is elastically deforming and will return to its original shape once unloaded. However, when a critical stress value is reached, plastic deformation begins. This stage sees substantial...
940