Related Experiment Video

Updated: Aug 25, 2025

Design and Characterization Methodology for Efficient Wide Range Tunable MEMS Filters
15:25

Design and Characterization Methodology for Efficient Wide Range Tunable MEMS Filters

Published on: February 4, 2018

6.2K

Analysis of an inverse weak-value tiltmeter in the kilohertz regime

Benjamin A Baldwin, Garrett K Josemans, John E Gray

    Applied Optics
    |October 18, 2022
    PubMed

    More Related Videos

    A Simple Approach to Perform TEER Measurements Using a Self-Made Volt-Amperemeter with Programmable Output Frequency07:43

    A Simple Approach to Perform TEER Measurements Using a Self-Made Volt-Amperemeter with Programmable Output Frequency

    Published on: October 5, 2019

    22.2K
    Spectral and Angle-Resolved Magneto-Optical Characterization of Photonic Nanostructures08:01

    Spectral and Angle-Resolved Magneto-Optical Characterization of Photonic Nanostructures

    Published on: November 21, 2019

    7.2K

    Related Concept Videos

    Mass Analyzers: Common Types01:19

    Mass Analyzers: Common Types

    The quadrupole mass analyzer consists of four cylindrical metal rods arranged in a diamond carrying a DC voltage and a radio-frequency AC voltage. The motion of ions through the quadrupole depends on the field strength, causing only ions of a certain m/z to resonate successfully and strike the detector at a given field strength. Though the transmission rate for these analyzers is high, the exact elemental composition of the sample is not determined because of low resolution; however, they are...
    684
    Voltammetric Techniques: Pulse Voltammetry01:17

    Voltammetric Techniques: Pulse Voltammetry

    Differential-pulse voltammetry (DPV) is a type of voltammetry that involves applying a series of voltage pulses to an electrochemical cell while measuring the resulting current. In DPV, the differential pulse or small potential pulses are superimposed on a linear potential sweep. The magnitude of these pulses is typically small, often in the millivolt range. Each voltage pulse lasts a short duration, usually in the order of a few milliseconds, and is applied at regular intervals along the...
    654
    Voltammetric Techniques: Linear-Scan (E vs Time)01:12

    Voltammetric Techniques: Linear-Scan (E vs Time)

    Polarography is a classical voltammetric technique used to analyze electrochemical reactions. This method applies a linear potential sweep to a dropping mercury electrode (DME), and the resulting current is measured. A dropping mercury electrode is commonly used as the working electrode in polarography. It consists of a capillary tube filled with mercury, where the tiny droplet forms at the tip. This droplet continuously drops from the capillary, creating a new electrode surface for each...
    473
    Voltammetry: Factors Affecting Measurements01:21

    Voltammetry: Factors Affecting Measurements

    A current produced due to the redox reactions of the analyte at the working and auxiliary electrodes is called a faradaic current. The reaction can be divided into two types. The current generated due to the reduction of the analyte is called cathodic current, and it carries a positive charge. In contrast, the current produced by analyte oxidation is known as an anodic current, and it has a negative charge. The applied potential at the working electrode determines the faradaic current flow, and...
    199
    Amperometry: Overview01:10

    Amperometry: Overview

    Amperometry is a technique commonly used to measure the concentration of specific analytes in a solution by monitoring the electric current generated during an electrochemical reaction. It involves applying a constant potential between a working electrode and a reference electrode to measure the resulting current, which is proportional to the concentration of the analyte. The Clark oxygen electrode operates based on this principle of amperometry. It consists of a cathode and an anode enclosed...
    690
    Inverting and Non-inverting OpAmps01:20

    Inverting and Non-inverting OpAmps

    In an inverting amplifier, the input voltage is connected through a resistor to the inverting terminal. Meanwhile, the non-inverting terminal is grounded and a feedback resistor is established between the inverting and output terminal, as depicted in Figure 1.
    895