Related Experiment Video

Updated: Aug 24, 2025

Achieving Moderate Pressures in Sealed Vessels Using Dry Ice As a Solid CO2 Source
06:26

Achieving Moderate Pressures in Sealed Vessels Using Dry Ice As a Solid CO2 Source

Published on: August 17, 2018

10.0K

Using greenhouse gases in the synthesis gas production processes: Thermodynamic conditions

Jerzy Szczygieł1, Katarzyna Chojnacka1, Dawid Skrzypczak1

  • 1Department of Advanced Material Technologies, Faculty of Chemistry, Wrocław University of Science and Technology, Smoluchowskiego 25, 50-372, Wrocław, Poland.

Journal of Environmental Management
|October 21, 2022
PubMed

Keywords:
H(2)/CO ratioMethane reformingOptimizationSyngasThermodynamic analysis

More Related Videos

Ammonia Synthesis at Low Pressure08:14

Ammonia Synthesis at Low Pressure

Published on: August 23, 2017

26.7K
Author Spotlight: Scaling Microalgal Biotechnology for Enhanced Biomethane Production07:34

Author Spotlight: Scaling Microalgal Biotechnology for Enhanced Biomethane Production

Published on: March 22, 2024

2.6K

Related Concept Videos

Hess's Law03:40

Hess's Law

There are two ways to determine the amount of heat involved in a chemical change: measure it experimentally, or calculate it from other experimentally determined enthalpy changes. Some reactions are difficult, if not impossible, to investigate and make accurate measurements for experimentally. And even when a reaction is not hard to perform or measure, it is convenient to be able to determine the heat involved in a reaction without having to perform an experiment.
45.6K
Chemical Stoichiometry and Gases: Using Ideal Gas Law to Determine Moles03:12

Chemical Stoichiometry and Gases: Using Ideal Gas Law to Determine Moles

Chemical stoichiometry describes the quantitative relationships between reactants and products in chemical reactions.
24.9K
Standard Enthalpy of Formation02:37

Standard Enthalpy of Formation

Enthalpy changes are typically tabulated for reactions in which both the reactants and products are at the same conditions. A standard state is a commonly accepted set of conditions used as a reference point for the determination of properties under other different conditions. For chemists, the IUPAC standard state refers to materials under a pressure of 1 bar and solutions at 1 M and does not specify a temperature. Many thermochemical tables list values with a standard state of 1 atm. Because...
42.3K
Thermochemical Equations02:55

Thermochemical Equations

For a chemical reaction (the system) carried out at constant pressure – with the only work done caused by expansion or contraction – the enthalpy of reaction (also called the heat of reaction, ΔHrxn) is equal to the heat exchanged with the surroundings (qp).
29.5K
Calculating Standard Free Energy Changes02:49

Calculating Standard Free Energy Changes

The free energy change for a reaction that occurs under the standard conditions of 1 bar pressure and at 298 K is called the standard free energy change. Since free energy is a state function, its value depends only on the conditions of the initial and final states of the system. A convenient and common approach to the calculation of free energy changes for physical and chemical reactions is by use of widely available compilations of standard state thermodynamic data. One method involves the...
21.7K
Radical Halogenation: Thermodynamics01:34

Radical Halogenation: Thermodynamics

The thermodynamic favorability of a reaction is determined by the change in Gibbs free energy (ΔG). ΔG has two components- enthalpy (ΔH) and entropy (ΔS). The entropy component is negligible for alkane halogenation because the number of reactants and product molecules are equal. In this case, the ΔG is governed only by the enthalpy component. The most crucial factor that determines ΔH is the strength of the bonds. ΔH can be determined by comparing the energy...
3.9K