Abundance and sources of plastic debris on beaches in a plastic hotspot, Nha Trang, Viet Nam

Related Experiment Video

Updated: Aug 18, 2025

Extraction of Organochlorine Pesticides from Plastic Pellets and Plastic Type Analysis
10:12

Extraction of Organochlorine Pesticides from Plastic Pellets and Plastic Type Analysis

Published on: July 1, 2017

11.6K

Mikkel Fruergaard1, Simon N Laursen1, Marianne N Larsen1

  • 1Department of Geosciences and Natural Resource Management (IGN), University of Copenhagen, Øster Voldgade 10, DK-1350 Copenhagen K, Denmark.

Marine Pollution Bulletin
|December 9, 2022
PubMed

Keywords:
Coastal and marine environmentFishing and aquaculture sectorsMacroplastic pollutionViet Nam

More Related Videos

Data Collection on Marine Litter Ingestion in Sea Turtles and Thresholds for Good Environmental Status13:18

Data Collection on Marine Litter Ingestion in Sea Turtles and Thresholds for Good Environmental Status

Published on: May 18, 2019

12.1K
Sampling, Sorting, and Characterizing Microplastics in Aquatic Environments with High Suspended Sediment Loads and Large Floating Debris05:31

Sampling, Sorting, and Characterizing Microplastics in Aquatic Environments with High Suspended Sediment Loads and Large Floating Debris

Published on: July 28, 2018

16.1K

Related Concept Videos

Plastic Behavior01:21

Plastic Behavior

A material's elastic behavior is characterized by the disappearance of stress once the load is removed, allowing the material to return to its original state. However, when stress surpasses the yield point, yielding commences, marking the onset of plastic deformation or permanent set. This change from elastic to plastic behavior is influenced by the peak stress value and the duration before the load is removed. An intriguing observation occurs when a specimen is loaded, unloaded, and...
248
Plastic Deformations01:19

Plastic Deformations

Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their...
168
Plasticity00:58

Plasticity

Plasticity is the property where an object loses its elasticity and undergoes irreversible deformation, even after the deformation forces are eliminated. If a material deforms irreversibly without increasing stress or load, then this is called ideal plasticity. For example, when a force is applied to an aluminum rod, it changes its shape, but it does not return to its original shape once the force is removed. Plastic deformation or ductility is thus a permanent deformation or change in the...
2.5K
Plastic Deformations of Members with a Single Plane of Symmetry01:21

Plastic Deformations of Members with a Single Plane of Symmetry

When a structural member undergoes plastic deformation due to bending, it is crucial to understand the position of the neutral axis and the stress distribution. This member, characterized by a single plane of symmetry, exhibits a uniform stress distribution, with negative stress above the neutral axis and positive stress below. Notably, the neutral axis does not align with the centroid of the cross-section. This misalignment is typical in cases where the cross-section is not rectangular or...
118
Plasticizers01:31

Plasticizers

Water-reducers, or plasticizers, are chemical admixtures used in concrete to improve strength and workability. These additives reduce the water-cement ratio without compromising workability, lower the cement content while maintaining the same workability, or increase workability to assist concrete placement in inaccessible areas.
Plasticizers function by using surface-active agents to create repulsive electrostatic forces between cement particles. This dispersion enhances the concrete's...
105
Primary Production01:06

Primary Production

The total amount of energy acquired by primary producers in an ecosystem is called gross primary production (GPP). However, of this energy, producers use some for metabolic processes, and some is lost as heat, decreasing the amount of energy available to the next trophic level. The remaining usable amount of energy is called the net primary productivity (NPP). In terrestrial ecosystems, NPP is driven by climate, while light penetration and nutrient availability drive NPP in aquatic ecosystems.
23.8K