Related Experiment Video

Updated: Aug 16, 2025

Experimental Investigation of the Hierarchical Control in DC Microgrids Using a Real-time Simulator
06:04

Experimental Investigation of the Hierarchical Control in DC Microgrids Using a Real-time Simulator

Published on: February 14, 2025

578

Improved Quasi-Z-Source High Step-Up DC-DC Converter Based on Voltage-Doubler Topology

Toru Sai1, Younghyun Moon1, Yasuhiro Sugimoto2

  • 1Faculty of Engineering, Tokyo Polytechnic University, Tokyo 243-0297, Kanagawa, Japan.

Sensors (Basel, Switzerland)
|December 23, 2022
PubMed

Keywords:
high step-up DC–DC converterhigh-side driver freelow voltage stressquasi-Z-sourcevoltage-doubler

More Related Videos

The Modular Design and Production of an Intelligent Robot Based on a Closed-Loop Control Strategy11:53

The Modular Design and Production of an Intelligent Robot Based on a Closed-Loop Control Strategy

Published on: October 14, 2017

11.7K
Silicon Metal-oxide-semiconductor Quantum Dots for Single-electron Pumping14:58

Silicon Metal-oxide-semiconductor Quantum Dots for Single-electron Pumping

Published on: June 3, 2015

14.8K

Related Concept Videos

Voltage Doubler Circuit01:23

Voltage Doubler Circuit

A voltage doubler circuit integrates two main components: a clamping section and a rectifier section. The clamping section consists of a capacitor (C1) and a diode (D1), whereas the rectifier section is equipped with another diode (D2) and capacitor (C2). This circuit produces an output voltage with twice the amplitude of the sinusoidal input voltage.
747
Bridge rectifier01:24

Bridge rectifier

The bridge rectifier is essential in electronics for efficiently converting alternating current (AC) to direct current (DC). Comprised of four diodes configured in a bridge layout, this rectifier effectively processes both the positive and negative halves of the AC waveform, making it superior to half-wave and full-wave center-tapped rectifiers in terms of voltage regulation and output stability.
Operationally, the bridge rectifier allows current flow through two of its diodes during each...
745
Half wave rectifier01:20

Half wave rectifier

A half-wave rectifier is a fundamental circuit in electronics, designed to convert alternating current (AC) voltage into a unidirectional voltage. It utilizes the simplest form of diode rectification, where the circuit comprises a single diode in series with a load resistor and an AC power source.
1.3K
Full wave rectifier01:22

Full wave rectifier

A full-wave rectifier is a device that converts alternating current (AC) to direct current (DC) and is more efficient than its half-wave counterpart. It typically includes a center-tapped transformer, two diodes, and a load resistor. The secondary winding of the transformer is divided to provide two equal voltages of opposite polarities, which is the pivotal element of full-wave rectification.
1.5K
Clamper Circuit01:14

Clamper Circuit

A clamper circuit, also known as a DC restorer, represents a specialized variant of the rectifier circuit, notable for its method of taking the output across the diode rather than the capacitor. This configuration lends to several distinctive applications, particularly in handling square wave inputs.
Within this circuit, the diode's orientation prompts the capacitor to charge up to the level of the most negative peak of the input signal. Upon reaching this state, the diode ceases to...
521
Design Example: Capacitance Multiplier Circuit01:20

Design Example: Capacitance Multiplier Circuit

In integrated circuit technology, a capacitance multiplier is often utilized to produce a larger capacitance value when a small physical capacitance falls short. This is achieved by a circuit that multiplies capacitance values by a factor of up to 1000, such that a 10-pF capacitor can replicate the performance of a 100-nF capacitor.
The circuit illustrated in Figure 1 below incorporates two op-amps, with the first operating as a voltage follower and the second acting as an inverting amplifier.
897