Related Experiment Video

Updated: Aug 15, 2025

Writing Bragg Gratings in Multicore Fibers
08:48

Writing Bragg Gratings in Multicore Fibers

Published on: April 20, 2016

8.2K

Behavior and measurement method of inter-core crosstalk in multicore fibers with core-dependent loss

Yuto Kobayashi, Tetsuya Hayashi

    Optics Express
    |January 6, 2023
    PubMed

    More Related Videos

    Measurement of Quantum Interference in a Silicon Ring Resonator Photon Source12:19

    Measurement of Quantum Interference in a Silicon Ring Resonator Photon Source

    Published on: April 4, 2017

    8.5K
    Transmission of Multiple Signals through an Optical Fiber Using Wavefront Shaping09:43

    Transmission of Multiple Signals through an Optical Fiber Using Wavefront Shaping

    Published on: March 20, 2017

    10.0K

    Related Concept Videos

    Reducing Line Loss01:18

    Reducing Line Loss

    In a three-phase circuit, line loss is an indicator of energy dissipated as heat due to the resistance of transmission lines. To address this, incorporating transformers into the system—a step-up transformer at the source and a step-down transformer at the load—is a strategic solution. Two three-phase transformers are introduced to improve this.
    With a step-up transformer at the source, the voltage is increased, thereby reducing the current in the transmission lines since power loss...
    185
    Transmission Line Design Considerations01:23

    Transmission Line Design Considerations

    Aluminum has become the material of choice for overhead transmission lines, surpassing copper due to its abundance and cost-effectiveness. The most prevalent type is the aluminum conductor, steel-reinforced (ACSR), which combines aluminum strands around a steel core. Other variants include all-aluminum conductors (AAC), all-aluminum alloy conductors (AAAC), aluminum conductor alloy-reinforced (ACAR), and aluminum-clad steel conductors. Advanced designs, such as aluminum conductors with steel...
    195
    Line Loss01:10

    Line Loss

    The different configurations of source-load connections include wye (star) and delta connections. The relationship between line and phase voltages and currents varies depending on the configuration. When the source is supplying power, it is transmitted through the wires to the load, and during this transmission, some power is absorbed by the wires, leading to line loss.
    Line loss impacts power delivery efficiency in a balanced three-phase circuit. The symmetry in such a circuit simplifies the...
    283
    Energy Stored In A Coaxial Cable01:31

    Energy Stored In A Coaxial Cable

    A coaxial cable consists of a central copper conductor used for transmitting signals, followed by an insulator shield, a metallic braided mesh that prevents signal interference, and a plastic layer that encases the entire assembly.
    In the simplest form, a coaxial cable can be represented by two long hollow concentric cylinders in which the current flows in opposite directions. The magnetic field inside and outside the coaxial cable is determined by using Ampère's law. The magnetic...
    1.6K
    Interference: Path Lengths01:10

    Interference: Path Lengths

    Consider two sources of sound, that may or may not be in phase, emitting waves at a single frequency, and consider the frequencies to be the same.
    Two special sources may be considered when they are in phase. This can be easily achieved by feeding the two sources from the same source. An example would be synchronizing the two speakers by feeding them with the same source, such as the sound waves produced by a tuning fork. This setup ensures that the two sources have the same frequency and are...
    1.4K
    Boundary Conditions: Lossless Lines01:21

    Boundary Conditions: Lossless Lines

    Consider a single-phase, two-wire, lossless transmission line terminated by an impedance at the receiving end and a source with Thevenin voltage and impedance at the sending end. The line, with length, has a surge impedance and wave velocity determined by the line's inductance and capacitance.
    At the receiving end, the boundary condition states that the voltage equals the product of the receiving-end impedance and current. This relationship is expressed as a function of the incident and...
    138