Related Experiment Video

Updated: Aug 12, 2025

WheelCon: A Wheel Control-Based Gaming Platform for Studying Human Sensorimotor Control
08:18

WheelCon: A Wheel Control-Based Gaming Platform for Studying Human Sensorimotor Control

Published on: August 15, 2020

5.0K

Existence and controllability for conformable fractional stochastic differential equations with infinite delay via

Jizhao Huang1, Danfeng Luo1

  • 1Department of Mathematics, Guizhou University, Guiyang, Guizhou 550025, China.

Chaos (Woodbury, N.Y.)
|February 1, 2023
PubMed

More Related Videos

Synthesis of Cyclic Polymers and Characterization of Their Diffusive Motion in the Melt State at the Single Molecule Level06:55

Synthesis of Cyclic Polymers and Characterization of Their Diffusive Motion in the Melt State at the Single Molecule Level

Published on: September 26, 2016

8.0K
Interactive and Visualized Online Experimentation System for Engineering Education and Research08:35

Interactive and Visualized Online Experimentation System for Engineering Education and Research

Published on: November 24, 2021

2.5K

Related Concept Videos

BIBO stability of continuous and discrete -time systems01:24

BIBO stability of continuous and discrete -time systems

System stability is a fundamental concept in signal processing, often assessed using convolution. For a system to be considered bounded-input bounded-output (BIBO) stable, any bounded input signal must produce a bounded output signal. A bounded input signal is one where the modulus does not exceed a certain constant at any point in time.
To determine the BIBO stability, the convolution integral is utilized when a bounded continuous-time input is applied to a Linear Time-Invariant (LTI) system....
473
Classification of Systems-II01:31

Classification of Systems-II

Continuous-time systems have continuous input and output signals, with time measured continuously. These systems are generally defined by differential or algebraic equations. For instance, in an RC circuit, the relationship between input and output voltage is expressed through a differential equation derived from Ohm's law and the capacitor relation,
198
Feedback control systems01:26

Feedback control systems

Feedback control systems are categorized in various ways based on their design, analysis, and signal types.
Linear feedback systems are theoretical models that simplify analysis and design. These systems operate under the principle that their output is directly proportional to their input within certain ranges. For instance, an amplifier in a control system behaves linearly as long as the input signal remains within a specific range. However, most physical systems exhibit inherent nonlinearity...
367
Linear Approximation in Time Domain01:21

Linear Approximation in Time Domain

Nonlinear systems often require sophisticated approaches for accurate modeling and analysis, with state-space representation being particularly effective. This method is especially useful for systems where variables and parameters vary with time or operating conditions, such as in a simple pendulum or a translational mechanical system with nonlinear springs.
For a simple pendulum with a mass evenly distributed along its length and the center of mass located at half the pendulum's length,...
113
Difference Equation Solution using z-Transform01:24

Difference Equation Solution using z-Transform

The z-transform is a powerful tool for analyzing practical discrete-time systems, often represented by linear difference equations. Solving a higher-order difference equation requires knowledge of the input signal and the initial conditions up to one term less than the order of the equation.
The z-transform facilitates handling delayed signals by shifting the signal in the z-domain, which corresponds to delaying the signal in the time domain, and advancing signals by similarly shifting in the...
344
Second Order systems II01:18

Second Order systems II

In an underdamped second-order system, where the damping ratio ζ is between 0 and 1, a unit-step input results in a transfer function that, when transformed using the inverse Laplace method, reveals the output response. The output exhibits a damped sinusoidal oscillation, and the difference between the input and output is termed the error signal. This error signal also demonstrates damped oscillatory behavior. Eventually, as the system reaches a steady state, the error diminishes to zero.
143