Related Experiment Video

Updated: Aug 10, 2025

Negative Additive Manufacturing of Complex Shaped Boron Carbides
06:45

Negative Additive Manufacturing of Complex Shaped Boron Carbides

Published on: September 18, 2018

8.7K

Coloration Modeling and Processing of Commodity Plastic Buttons in Supercritical Carbon Dioxide

Kota Kobayashi1, Tierong Bai1,2, Kazuhiro Tamura1

  • 1School of Natural System, College of Science and Engineering, Kanazawa University, Kakuma-machi, Kanazawa 920-1192, Japan.

Materials (Basel, Switzerland)
|February 11, 2023
PubMed

Keywords:
K/S valuediffusion–adsorption modeldyeingplastic buttonscCO2solubility

More Related Videos

Microfluidic Fabrication Techniques for High-Pressure Testing of Microscale Supercritical CO2 Foam Transport in Fractured Unconventional Reservoirs10:06

Microfluidic Fabrication Techniques for High-Pressure Testing of Microscale Supercritical CO2 Foam Transport in Fractured Unconventional Reservoirs

Published on: July 2, 2020

6.9K
Multimodal 3D Printing of Phantoms to Simulate Biological Tissue05:11

Multimodal 3D Printing of Phantoms to Simulate Biological Tissue

Published on: January 11, 2020

7.6K

Related Concept Videos

Plasticizers01:31

Plasticizers

Water-reducers, or plasticizers, are chemical admixtures used in concrete to improve strength and workability. These additives reduce the water-cement ratio without compromising workability, lower the cement content while maintaining the same workability, or increase workability to assist concrete placement in inaccessible areas.
Plasticizers function by using surface-active agents to create repulsive electrostatic forces between cement particles. This dispersion enhances the concrete's...
101
Plastic Behavior01:21

Plastic Behavior

A material's elastic behavior is characterized by the disappearance of stress once the load is removed, allowing the material to return to its original state. However, when stress surpasses the yield point, yielding commences, marking the onset of plastic deformation or permanent set. This change from elastic to plastic behavior is influenced by the peak stress value and the duration before the load is removed. An intriguing observation occurs when a specimen is loaded, unloaded, and...
244
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
118
Superplasticizers01:30

Superplasticizers

Superplasticizers are advanced admixtures that enhance the workability of concrete by lowering the water content without compromising the strength of the material. These substances are highly effective water reducers, improving concrete flow, making it easier to work with, and enabling concrete to reach inaccessible areas or densely reinforced sections without mechanical vibration. The key components in superplasticizers are either sulfonated melamine or naphthalene formaldehyde condensates,...
109
Phase Diagrams02:39

Phase Diagrams

A phase diagram combines plots of pressure versus temperature for the liquid-gas, solid-liquid, and solid-gas phase-transition equilibria of a substance. These diagrams indicate the physical states that exist under specific conditions of pressure and temperature and also provide the pressure dependence of the phase-transition temperatures (melting points, sublimation points, boiling points). Regions or areas labeled solid, liquid, and gas represent single phases, while lines or curves represent...
42.3K
Sublimation01:03

Sublimation

Sublimation is the direct transformation of a solid to a gaseous state. For instance, at standard pressure and room temperature, solid carbon dioxide sublimes to gaseous carbon dioxide. The phase diagram depicts the conditions required for sublimation. This process occurs at the solid-gas phase boundary and is not observed above the triple point of the substance. The reverse of sublimation is called deposition, where a gaseous substance condenses directly into a solid. Sublimation and...
798