Related Experiment Video

Updated: Aug 10, 2025

Twin-Screw Extrusion Process to Produce Renewable Fiberboards
07:21

Twin-Screw Extrusion Process to Produce Renewable Fiberboards

Published on: January 27, 2021

6.5K

Influence of Particle Size and Bulk Density on Sound Absorption Performance of Oil Palm Frond-Reinforced Composites

Budi Istana1,2, I Made Londen Batan1, Sutikno1

  • 1Department of Mechanical Engineering, Institut Teknologi Sepuluh Nopember (ITS), Surabaya 60111, Indonesia.

Polymers
|February 11, 2023
PubMed

Keywords:
acoustic absorbercompositeoil palm frondparticleboardssound absorption coefficient

More Related Videos

The Effect of Construction and Demolition Waste Plastic Fractions on Wood-Polymer Composite Properties09:06

The Effect of Construction and Demolition Waste Plastic Fractions on Wood-Polymer Composite Properties

Published on: June 7, 2020

8.1K
Fabrication and Design of Wood-Based High-Performance Composites08:08

Fabrication and Design of Wood-Based High-Performance Composites

Published on: November 9, 2019

13.4K

Related Concept Videos

Wood Panel Products01:18

Wood Panel Products

Wood panel products are essential materials used in construction for applications such as flooring, siding, and roofing, typically available in standard dimensions of 4 feet by 8 feet, with thicknesses varying from one-quarter of an inch to one and one-eighth inches. Among the most common types of wood panels is plywood, which is produced by gluing multiple layers of thin wood veneers under pressure. The grain of the outer veneers runs lengthwise, while the grains of the interior layers run...
105
Porosity and Absorption of Aggregate01:20

Porosity and Absorption of Aggregate

Aggregates contain pores of varying sizes; while some are completely enclosed within the particles, others open onto the surface, allowing water to penetrate. The porosity of aggregates is a major factor contributing to the overall porosity of concrete, given that aggregates constitute about three-quarters of concrete's volume.
When all pores in an aggregate are filled with water, the aggregate is considered saturated and surface-dry. If left in dry air, water will evaporate until the...
349
Bulk Density of Aggregate01:22

Bulk Density of Aggregate

Bulk density refers to the mass of aggregate particles that would fill a unit volume. The concept of bulk density originates from the inability to pack aggregate particles in a manner that completely eliminates void spaces. Hence, the term bulk refers to the volume that encompasses both the aggregates and the voids. This measurement is crucial when aggregates are batched by volume and is used to convert quantities by mass to volume.
Most natural mineral aggregates, like sand and gravel,...
557
Moisture Content and Bulking of Aggregate01:10

Moisture Content and Bulking of Aggregate

The moisture content of aggregates is a crucial factor in construction, particularly in concrete mixing, as it influences the total water required in the mix. Moisture content represents the water coated on the exterior surface of the aggregate existing in a saturated and surface-dry condition. The total water content of a moist aggregate is the sum of its moisture content and water absorption.
When aggregates are exposed to rain or sit in stockpiles, they absorb moisture, which must be...
189
Speed of Sound in Solids and Liquids00:51

Speed of Sound in Solids and Liquids

Most solids and liquids are incompressible—their densities remain constant throughout. In the presence of an external force, the molecules tend to restore to their original positions, which is only possible because the constituents interact. The interactions help the constituents pass on information about external disturbances, like sound waves. Therefore, sound waves travel faster through these media. Compared to solids, the constituents in a liquid are less tightly bound. Thus, sound...
3.1K
Structural Properties and Dimensions of Lumber01:21

Structural Properties and Dimensions of Lumber

Wood's structural properties derive from fibers aligned along the tree's length, contributing significantly to its mechanical strength. Wood exhibits up to twenty times greater tensile strength along these fibers compared to across them, and generally shows better performance under compression than tension. The length of fibers varies, with hardwoods having fibers around one twenty-fifth inch long and softwoods ranging from one-eighth to one-third inch.
The strength characteristics of...
149