Related Experiment Video

Updated: Aug 10, 2025

Fiber Optic Distributed Sensors for High-resolution Temperature Field Mapping
09:48

Fiber Optic Distributed Sensors for High-resolution Temperature Field Mapping

Published on: November 7, 2016

12.1K

Simultaneous Measurement of Strain and Temperature Distributions Using Optical Fibers with Different GeO2 and B2O3

Shinsaku Hisada1, Utanori Kodakamine2, Daichi Wada1

  • 1Japan Aerospace Exploration Agency, Tokyo 181-0015, Japan.

Sensors (Basel, Switzerland)
|February 11, 2023
PubMed

Keywords:
distributed measurementerror propagationfiber Bragg gratingoptical fiberstrain and temperature

More Related Videos

Production of a Strain-Measuring Device with an Improved 3D Printer06:17

Production of a Strain-Measuring Device with an Improved 3D Printer

Published on: January 30, 2020

6.2K
Optimized Sealing Process and Real-Time Monitoring of Glass-to-Metal Seal Structures04:41

Optimized Sealing Process and Real-Time Monitoring of Glass-to-Metal Seal Structures

Published on: September 2, 2019

7.4K

Related Concept Videos

Measurements of Strain01:27

Measurements of Strain

Strain quantifies the deformation of a material under force, typically measured as normal strain, which represents the change in length when compared with the original length. Electrical strain gauges are used for enhanced accuracy. These devices consist of a conductive wire mounted on a paper backing that adheres to the material's surface. These gauges operate on the piezoresistive effect, where the wire's electrical resistance changes in response to mechanical deformation. The strain...
1.8K
Thermal Strain01:19

Thermal Strain

Thermal strain is a concept that arises when we consider how temperature changes affect structures. Unlike the conventional assumption that structures remain constant under load, real-world scenarios often involve temperature fluctuations that can significantly impact these structures. Consider a homogeneous rod with a uniform cross-section resting freely on a flat horizontal surface. If the rod's temperature increases, the rod elongates. This elongation is proportional to the temperature...
2.1K
Strain and Elastic Modulus01:15

Strain and Elastic Modulus

The quantity that describes the deformation of a body under stress is known as strain. Strain is given as a fractional change in either length, volume, or geometry under tensile, volume (also known as bulk), or shear stress, respectively, and is a dimensionless quantity. The strain experienced by a body under tensile or compressive stress is called tensile or compressive strain, respectively. In contrast, the strain experienced under bulk stress and shear stress is known as volume and shear...
4.0K
Three-Dimensional Analysis of Strain01:29

Three-Dimensional Analysis of Strain

Three-dimensional strain analysis is crucial for understanding how materials deform under stress, particularly in elastic, homogeneous materials. This method employs principal stress axes to simplify complex stress states into more understandable forms. Subjected to stress, a small cubic element within a material either expands or contracts along these axes, transforming into a rectangular parallelepiped. This transformation effectively illustrates the material's deformation. The principal...
273
Design Example: Strain Gauge Bridge or Wheatstone Bridge01:15

Design Example: Strain Gauge Bridge or Wheatstone Bridge

The utilization of strain gauges as transducers for converting mechanical strain into electrical signals is a common practice in various engineering applications. These strain gauges are frequently integrated into Wheatstone bridge circuits to accurately measure parameters such as force or pressure. Within this context, each element within the circuit exhibits a resistance that undergoes subtle variations when subjected to mechanical strain. The primary objective is to convert minuscule...
473
Stress-Strain Diagram01:10

Stress-Strain Diagram

A stress-strain diagram is a crucial tool that graphically displays a material's mechanical characteristics. This diagram is derived from a tensile test performed on a carefully prepared cylindrical specimen. The specimen has two gauge marks inscribed on its central part, and the distance between these marks is known as the gauge length. The cylindrical specimen is placed in a testing machine, which applies an increasing centric load. As this load grows, so does the gauge length. This...
742