Related Experiment Video

Updated: Aug 10, 2025

Experimental Methodology for Estimation of Local Heat Fluxes and Burning Rates in Steady Laminar Boundary Layer Diffusion Flames
10:29

Experimental Methodology for Estimation of Local Heat Fluxes and Burning Rates in Steady Laminar Boundary Layer Diffusion Flames

Published on: June 1, 2016

11.9K

The 3D-Dynamic Fire Risk Evaluation Method of Modern Logistics Warehouses: A Modified Gustav Method

Wenhui Ju1, Guofeng Su1, Lizhi Wu2

  • 1Department of Engineering Physics, Tsinghua University, Heqing Road, Haidian, Beijing, 100084 China.

Fire Technology
|February 13, 2023
PubMed

Keywords:
3-Dimension modelEmergency resilienceFire risk levelFire safety managementLogistics warehouseSemi-quantitative evaluation

More Related Videos

Design and Optimization Strategies of a High-Performance Vented Box14:23

Design and Optimization Strategies of a High-Performance Vented Box

Published on: June 9, 2023

1.2K
Blast Quantification Using Hopkinson Pressure Bars09:41

Blast Quantification Using Hopkinson Pressure Bars

Published on: July 5, 2016

9.1K

Related Concept Videos

Design Example: Analyzing Capacity Contours for Flood Risk Assessment01:17

Design Example: Analyzing Capacity Contours for Flood Risk Assessment

Flood risk assessment involves careful planning and analysis to ensure the safety of communities near water retention structures. Capacity contours are a vital tool in this process, as they illustrate the potential spread of water at specific levels in a given area. In the context of building a bund across a small valley, these contours play a critical role in evaluating the safety of nearby residential areas.In this example, the bund is intended to store stormwater in the valley. The engineers...
86
Design Example: Calculating Safe Diameter for Wind-Exposed Disc01:17

Design Example: Calculating Safe Diameter for Wind-Exposed Disc

Assessing safety in wind-exposed installations is crucial to preventing potential failures. This example explores the calculation and design adjustments needed to mount a circular disc on a building facade, where wind forces are a primary concern. A 4-meter diameter disc was initially designed as an aesthetic feature facing winds at a velocity of 25 meters per second, with an air density of 1.25 kilograms per cubic meter. Given these conditions, the drag force on the disc was determined using...
169
Dynamic Modulus of Elasticity of Concrete01:16

Dynamic Modulus of Elasticity of Concrete

The dynamic modulus of elasticity assesses how a concrete structure deforms under impact or dynamic loads. It is typically higher than the static modulus of elasticity, measured under slow, steady loading conditions.
The sonic test is a common method to determine the dynamic modulus. In this test, a concrete beam, sized either 6 x 6 x 30 inches or 4 x 4 x 20 inches, is clamped at its center. Vibrations are initiated at one end of the beam by an electromagnetic exciter unit powered by...
452
Resultant of a General Distributed Loading01:13

Resultant of a General Distributed Loading

While designing structures exposed to non-uniform loads, it is crucial to consider the resultant force and its location. This resultant force is a single vector representing the net force applied due to the distributed load.
Examples such as load distribution due to wind and load distribution on a bridge illustrate how this concept is used to analyze and design safe, reliable structures under variable loading conditions. Most structures, such as residential buildings, bridges, and towers, are...
724
Three-Dimensional Force System01:30

Three-Dimensional Force System

In mechanical engineering, a three-dimensional force system is a system of forces acting in three dimensions, with forces applied along the x, y, and z coordinate axes. The three-dimensional force system is an important concept in mechanical engineering, as it allows engineers to understand and analyze the behavior of objects and structures in three dimensions. By understanding the forces acting on a system, engineers can design more efficient and effective mechanical systems that can withstand...
2.1K
Internal Loadings in Structural Members: Problem Solving01:28

Internal Loadings in Structural Members: Problem Solving

When designing or analyzing a structural member, it is important to consider the internal loadings developed within the member. These internal loadings include normal force, shear force, and bending moment. Engineers can ensure that the structural member can support the applied external forces by calculating these internal loadings.
To illustrate this, let's consider a beam OC of 5 kN, inclined at an angle of 53.13° with the horizontal and supported at both ends. Determine the internal...
1.3K