Related Experiment Video

Updated: Aug 6, 2025

Modeling and Experimental Analysis of the Single-Shaft Coaxial Motor-Pump Assembly in Electrohydrostatic Actuators
08:59

Modeling and Experimental Analysis of the Single-Shaft Coaxial Motor-Pump Assembly in Electrohydrostatic Actuators

Published on: June 13, 2022

2.6K

A comparative study of structural parameters for spiral groove bearing in centrifugal rotary blood pump

Cong Xue1, Yu Chen2, Bin Zhu3

  • 1Department of Cardiology, The Third Affiliated Hospital of Soochow University, Changzhou 213003, China.

Heliyon
|March 21, 2023
PubMed

Keywords:
Blood filmHydrodynamic performanceSpiral groove bearingStructural parameter

More Related Videos

A Modeling and Simulation Method for Preliminary Design of an Electro-Variable Displacement Pump09:04

A Modeling and Simulation Method for Preliminary Design of an Electro-Variable Displacement Pump

Published on: June 1, 2022

3.1K
A Cost-effective and Reliable Method to Predict Mechanical Stress in Single-use and Standard Pumps07:34

A Cost-effective and Reliable Method to Predict Mechanical Stress in Single-use and Standard Pumps

Published on: August 5, 2015

9.5K

Related Concept Videos

Design Example: Deciding Thickness of Lubricating Fluid in a Shaft01:23

Design Example: Deciding Thickness of Lubricating Fluid in a Shaft

Effective lubrication between a rotating shaft and its bearing housing is essential in rotating machinery to minimize friction, wear, and energy loss. With carefully controlled thickness and viscosity, the lubricant layer prevents metal-to-metal contact, ensuring smooth operation.
To calculate the required thickness of the lubricant layer, the tangential velocity at the shaft's surface must first be determined. This velocity is calculated by converting the rotational speed to angular...
141
Residual Stresses in Circular Shafts01:10

Residual Stresses in Circular Shafts

In materials that exhibit elastic and plastic behavior, known as elastoplastic materials, residual stresses can accumulate when these materials experience plastic deformation. This deformation arises from either high levels of shearing stress or significant strains. Residual stresses are internal stresses that persist within a material after removing the external force causing deformation. This phenomenon is demonstrated when observing the behavior of a shaft under torque; notably, the...
210
Stress Concentrations in Circular Shafts01:18

Stress Concentrations in Circular Shafts

Consider the elastic torsion formula, which applies to a circular shaft with a consistent cross-section. This formula assumes that the shaft's ends are loaded with rigid plates firmly attached. However, in many cases, torques are applied to the shaft through mechanisms like flange couplings or gears, which are connected by keys inserted into keyways. This application method modifies the stress distribution near the point of torque application, causing it to deviate from the distributions...
214
Pivot Bearings01:23

Pivot Bearings

In mechanical systems, bearings are crucial in facilitating relative motion between two components while minimizing friction and wear. They help distribute various loads (radial, axial or a combination of both loads) across machinery parts, ensuring smooth and efficient operation.
A pivot bearing is a specialized type of bearing designed to support axial loads on a rotating shaft. The bearing surface, or the pivot, is positioned at the end of a shaft to support the axial thrust. The pivot may...
1.4K
Circular Shaft - Stresses in Linear Range01:13

Circular Shaft - Stresses in Linear Range

Consider a scenario where a circular shaft is subject to torque that remains within the boundaries of Hooke's Law, avoiding any permanent deformation. So, the formula for shearing strain is revisited. This formula is multiplied by the modulus of rigidity, and then Hooke's Law for the shearing stress and strain is applied. As a result, the equation for shearing stress in a shaft can be derived.
327
Transmission Shafts: Problem Solving01:09

Transmission Shafts: Problem Solving

Designing a solid shaft that transmits power from a motor to a machine tool involves a series of calculations to ensure the shaft can withstand the stresses applied by bending moments and torques. First, calculate the torque exerted on the gear, considering the power transmitted by the shaft and its rotational speed. Following this, compute the tangential forces acting on the gears, which directly relate to the torque and the gear radius.
Next, use bending moment diagrams for the shaft to...
273