Related Experiment Video

Updated: Jul 31, 2025

Design and Construction of a Cost Effective Headstage for Simultaneous Neural Stimulation and Recording in the Water Maze
09:09

Design and Construction of a Cost Effective Headstage for Simultaneous Neural Stimulation and Recording in the Water Maze

Published on: October 13, 2010

10.7K

Design and fabrication of a GaN HEMT power amplifier based on hidden Markov model for wireless applications

Mohammad Soruri1, S Mohammad Razavi1, Mehdi Forouzanfar1

  • 1Faculty of Electrical and Computer Engineering, University of Birjand, Birjand, Iran.

Plos One
|May 5, 2023
PubMed

More Related Videos

Autonomous and Rechargeable Microneurostimulator Endoscopically Implantable into the Submucosa08:17

Autonomous and Rechargeable Microneurostimulator Endoscopically Implantable into the Submucosa

Published on: September 27, 2018

8.5K
Characterization of Anisotropic Leaky Mode Modulators for Holovideo09:36

Characterization of Anisotropic Leaky Mode Modulators for Holovideo

Published on: March 19, 2016

8.0K

Related Concept Videos

Design Example: Vintage Mixing Console01:17

Design Example: Vintage Mixing Console

A sound engineer at a music company recently encountered a problem. The output from their newly acquired studio's vintage mixing console was too low for the requirements of modern recording equipment. To rectify this situation, the engineer decided to design an audio pre-amplifier using an operational amplifier (op-amp) to boost the signal level.
The specifications for the pre-amplifier were clear. It needed to amplify the audio signal by a factor of 10, have an input impedance above 10...
260
MOSFET Amplifiers01:17

MOSFET Amplifiers

The MOSFET, when operating in its active region, functions as a voltage-controlled current source. In this region, the gate-to-source voltage controls the drain current. This principle underlies the operation of the transconductance MOSFET amplifier. The output current is directed through a load resistor to convert this amplifier into a voltage amplifier. The output voltage is then obtained by subtracting the voltage drop across the load resistance from the supply voltage. This process results...
188
Small-Signal Analysis of MOSFET Amplifiers01:23

Small-Signal Analysis of MOSFET Amplifiers

In small-signal analysis, a MOSFET transistor amplifier acts as a linear amplifier when operating in its saturation region. The gate-to-source voltage (VGS) of the MOSFET is the sum of the DC biasing voltage and the small time-varying input signal. This combination sets up the operating point and modulates the drain current (ID) that flows from the drain to the source. When a small AC signal is superimposed on the DC bias voltage at the gate, the instantaneous drain current comprises three...
626
Small-Signal Analysis of BJT Amplifiers01:21

Small-Signal Analysis of BJT Amplifiers

Small signal analysis is a fundamental approach used in electronics to understand how a Bipolar Junction Transistor (BJT) amplifier processes signals. In the active region, the BJT is designed for linear amplification. The transistor's behavior under these conditions is governed by its instantaneous base-emitter voltage VBE, a sum of the DC bias VBE, and a small AC signal VBE, resulting in the collector current iC. Here, the collector current has a DC component and an AC component.
1.2K
BJT Amplifiers01:14

BJT Amplifiers

Bipolar Junction Transistors (BJTs) are pivotal components in amplifier circuits, functioning as voltage-controlled current sources in their active region. This characteristic allows them to efficiently control the collector current through variations in the base-emitter voltage. Essentially, BJTs amplify power due to their ability to take a weak input signal and output a much stronger signal.
In BJT amplifier configurations, particularly in common-emitter setups, the transistor's role...
533
Maximum Power Transfer01:16

Maximum Power Transfer

Numerous practical applications within engineering disciplines, such as telecommunications, necessitate optimizing power delivery to a connected load. This pursuit, however, entails inherent internal losses, which can either equal or exceed the power supplied to the load. The Thevenin equivalent circuit is helpful in finding the maximum power a linear circuit can deliver to a load. It is assumed in this context that the load resistance can be adjusted.
By substituting the entire circuit with...
305