Related Experiment Video

Updated: Jul 28, 2025

Quasistatic Mechanical Testing for Computer-Aided Design and Manufacturing Occlusal Veneers Cemented to Milled Dentin Analog Material
07:42

Quasistatic Mechanical Testing for Computer-Aided Design and Manufacturing Occlusal Veneers Cemented to Milled Dentin Analog Material

Published on: December 20, 2024

431

RETENTIVE STRENGTH OF CEMENTRETAINED IMPLANT-SUPPORTED FIXED DENTAL PROSTHESES ACCORDING TO DIFFERENT CEMENT TYPES

Gi Young Kim, Ha Eun Choi, You-Jung Kang

    The International Journal of Prosthodontics
    |May 31, 2023
    PubMed
    Abstract

    More Related Videos

    Oral Biofilm Formation on Different Materials for Dental Implants11:19

    Oral Biofilm Formation on Different Materials for Dental Implants

    Published on: June 24, 2018

    11.6K
    An Improved Mechanical Testing Method to Assess Bone-implant Anchorage11:51

    An Improved Mechanical Testing Method to Assess Bone-implant Anchorage

    Published on: February 10, 2014

    15.5K

    Related Concept Videos

    Strength of Cement01:20

    Strength of Cement

    Strength tests for cement are not performed directly on neat cement paste due to difficulty in obtaining consistent, reliable specimens. Instead, cement is typically tested in the form of cement-sand mortar.
    For compressive strength tests, ASTM C 109-05 standards prescribe a cement-sand mix ratio of 1:2.75 and a water/cement ratio of 0.485 for making 2-inch cubes. These cubes are mixed, cast, and cured in saturated lime water at 23°C until testing. Flexural strength testing, outlined in...
    175
    Types of Cement II01:22

    Types of Cement II

    Portland blast-furnace cement is made by blending Portland cement clinker with granulated blast-furnace slag, which accounts for 25 to 65 percent of the cement's weight. Despite its similarities to ordinary Portland (Type I) cement in terms of fineness and setting times, its early strength is lower, though it achieves comparable strength later on. It's particularly suited for mass concrete structures and marine environments due to its lower heat of hydration and superior sulfate...
    139
    Types of Cement I01:21

    Types of Cement I

    Portland cement comes in several types, each with distinct properties and applications based on their chemical composition and hydration characteristics:
    Type I (Ordinary Portland Cement) is widely used for general construction where special properties are not required. It has moderate sulfate resistance and heat of hydration.
    Type II (Modified Cement) offers moderate resistance to sulfate attack and a lower rate of heat development compared to Type I. It is suitable for structures in...
    161
    Bonding and Strength of Aggregate01:12

    Bonding and Strength of Aggregate

    The bond between aggregate particles and the cement matrix is significantly influenced by the shape and surface texture of the aggregates. High-strength concretes benefit from a rougher texture, which leads to stronger bonding due to greater adhesion. Angular aggregates with larger surface areas also enhance this bond. The bonding quality, however, is complex to assess as no universally accepted test exists. Good bonding is indicated when a crushed concrete specimen shows some aggregate...
    224
    Mortar Properties01:17

    Mortar Properties

    Mortar properties encompass a range of characteristics crucial for construction and masonry work, including workability, water retention, bond strength, durability, compressive strength, volume change, and appearance. Workability refers to mortar's ability to be easily applied and manipulated without sagging or falling off surfaces, which is important for efficient masonry unit placement and alignment. Water retention is essential to prevent the mortar from losing moisture too quickly to...
    157
    Tensile Strength Considerations of Concrete01:16

    Tensile Strength Considerations of Concrete

    Considering the tensile strength of concrete involves recognizing that the theoretical strength of cement paste can be up to a thousand times higher than what is observed in practical applications. This significant discrepancy is largely attributed to the presence of microscopic cracks within the concrete. These cracks tend to amplify stress at their tips when a load is applied, a phenomenon explained by Griffith's theory of brittle fracture.
    The dimensions and shape of a concrete specimen...
    157