Related Experiment Video
Updated: Jul 21, 2025
Synthesis of Platinum-nickel Nanowires and Optimization for Oxygen Reduction Performance
Published on: April 27, 2018
Development of Hydrogen-Oxygen Fuel Cells Based on Anion-Exchange Electrolytes and Catalysts with Reduced Platinum
Oleg Korchagin1, Vera Bogdanovskaya1, Inna Vernigor1
1Frumkin Institute of Physical Chemistry and Electrochemistry, Russian Academy of Sciences, 119071 Moscow, Russia.
Abstract:
Studies have been carried out to optimize the composition, formation technique and test conditions of membrane electrode assemblies (MEA) of hydrogen-oxygen anion-exchange membranes fuel cells (AEMFC), based on Fumatech anion-exchange membranes. A non-platinum catalytic system based on nitrogen-doped CNT (CNTN) was used in the cathode. PtMo/CNTN catalysts with a reduced content of platinum (10-12 wt.% Pt) were compared with 10 and 60 wt.% Pt/CNTN at the anode. According to the results of studies under model conditions, it was found that the PtMo/CNTN catalyst is significantly superior to the 10 and 60 wt.% Pt/CNTN catalyst in terms of activity in the hydrogen oxidation reaction based on the mass of platinum. The addition of the Fumion ionomer results in minor changes in the electrochemically active surface area and activity in the hydrogen oxidation reaction for each of the catalysts. In this case, the introduction of ionomer-Fumion leads to a partial blocking of the outer surface and the micropore surface, which is most pronounced in the case of the 60Pt/CNTN catalyst. This effect can cause a decrease in the characteristics of MEA AEMFC upon passing from 10PtMo/CNTN to 60Pt/CNTN in the anode active layer. The maximum power density of the optimized MEA based on 10PtMo/CNTN was 62 mW cm-2, which exceeds the literature data obtained under similar test conditions for MEA based on platinum cathode and anode catalysts and Fumatech membranes (41 mW cm-2). A new result of this work is the study of the effect of the ionomer (Fumion) on the characteristics of catalysts. It is shown that the synthesized 10PtMo/CNTN catalyst retains high activity in the presence of an ionomer under model conditions and in the MEA based on it.
More Related Videos
06:39Author Spotlight: Design and Evaluation of Au-Electroplated Carbon Fiber Cloth Electrodes for Hydrogen Peroxide Fuel Cells
Published on: October 20, 2023
09:18Simple Methods for the Preparation of Non-noble Metal Bulk-electrodes for Electrocatalytic Applications
Published on: June 21, 2017
Related Concept Videos
02:13Reduction of Alkenes: Catalytic Hydrogenation
Metals like palladium, platinum, and nickel are commonly used in their solid forms — fine powder on an inert surface. As these catalysts remain insoluble in the reaction mixture, they are referred to as heterogeneous catalysts.
The hydrogenation process takes place on the...
03:12Batteries and Fuel Cells
02:17Reduction of Alkenes: Asymmetric Catalytic Hydrogenation
The metal catalyst used can be either heterogeneous or homogeneous. When hydrogenation of an alkene generates a chiral center, a pair of enantiomeric products is expected to form. However, an enantiomeric excess of one of the products can be facilitated using an enantioselective reaction or an...
02:24Reduction of Alkynes to cis-Alkenes: Catalytic Hydrogenation
Like alkenes, alkynes can be reduced to alkanes in the presence of transition metal catalysts such as Pt, Pd, or Ni. The reaction involves two sequential syn additions of hydrogen via a cis-alkene intermediate.
02:50Catalysis
02:23Alcohols from Carbonyl Compounds: Reduction
Catalytic hydrogenation is similar to the reduction of an alkene or alkyne by adding H2 across the pi bond in the presence of transition metal catalysts like Raney Ni, Pd–C, Pt, or Ru. Aldehydes and ketones can be reduced by this method, often under mild to moderate heat (25–100°C) and...