Related Experiment Video

Updated: Jul 18, 2025

High-Contrast and Fast Photorheological Switching of a Twist-Bend Nematic Liquid Crystal
06:24

High-Contrast and Fast Photorheological Switching of a Twist-Bend Nematic Liquid Crystal

Published on: October 31, 2019

6.5K

Modeling Viscoelasticity and Dynamic Nematic Order of Exchangeable Liquid Crystal Elastomers

Jiameng Zhao1,2, Fanlong Meng1,2,3

  • 1CAS Key Laboratory of Theoretical Physics, Institute of Theoretical Physics, Chinese Academy of Sciences, Beijing 100190, China.

Physical Review Letters
|August 25, 2023
PubMed

More Related Videos

Microfluidic Preparation of Liquid Crystalline Elastomer Actuators12:04

Microfluidic Preparation of Liquid Crystalline Elastomer Actuators

Published on: May 20, 2018

9.0K
Preparation of Monodomain Liquid Crystal Elastomers and Liquid Crystal Elastomer Nanocomposites12:21

Preparation of Monodomain Liquid Crystal Elastomers and Liquid Crystal Elastomer Nanocomposites

Published on: February 6, 2016

12.7K

Related Concept Videos

Members Made of Elastoplastic Material01:19

Members Made of Elastoplastic Material

The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
As the bending moment...
121
The Fluid Mosaic Model01:34

The Fluid Mosaic Model

The fluid mosaic model was first proposed as a visual representation of research observations. The model comprises the composition and dynamics of membranes and serves as a foundation for future membrane-related studies. The model depicts the structure of the plasma membrane with a variety of components, which include phospholipids, proteins, and carbohydrates. These integral molecules are loosely bound, defining the cell’s border and providing fluidity for optimal function.
148.9K
Elastic Strain Energy for Shearing Stresses01:20

Elastic Strain Energy for Shearing Stresses

As discussed in previous lessons, strain energy in a material is the energy stored when it is elastically deformed, a concept crucial in materials science and mechanical engineering. This energy results from the internal work done against the cohesive forces within the material. When a material undergoes shearing stress and corresponding shearing strain, the strain energy density, which is the energy stored per unit volume, is calculated. Within the elastic limit, where the stress is...
217
Dynamic Modulus of Elasticity of Concrete01:16

Dynamic Modulus of Elasticity of Concrete

The dynamic modulus of elasticity assesses how a concrete structure deforms under impact or dynamic loads. It is typically higher than the static modulus of elasticity, measured under slow, steady loading conditions.
The sonic test is a common method to determine the dynamic modulus. In this test, a concrete beam, sized either 6 x 6 x 30 inches or 4 x 4 x 20 inches, is clamped at its center. Vibrations are initiated at one end of the beam by an electromagnetic exciter unit powered by...
388
Plastic Behavior01:21

Plastic Behavior

A material's elastic behavior is characterized by the disappearance of stress once the load is removed, allowing the material to return to its original state. However, when stress surpasses the yield point, yielding commences, marking the onset of plastic deformation or permanent set. This change from elastic to plastic behavior is influenced by the peak stress value and the duration before the load is removed. An intriguing observation occurs when a specimen is loaded, unloaded, and...
222
Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity01:15

Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity

Deformation occurs in axial and transverse directions when an axial load is applied to a slender bar. This deformation impacts the cubic element within the bar, transforming it into either a rectangular parallelepiped or a rhombus, contingent on its orientation. This transformation process induces shearing strain. Axial loading elicits both shearing and normal strains. Applying an axial load instigates equal normal and shearing stresses on elements oriented at a 45° angle to the load axis.
290