Related Experiment Video

Updated: Jul 16, 2025

Macro-Rheology Characterization of Gill Raker Mucus in the Silver Carp, Hypophthalmichthys molitrix
09:13

Macro-Rheology Characterization of Gill Raker Mucus in the Silver Carp, Hypophthalmichthys molitrix

Published on: July 10, 2020

3.2K

Investigation the Effect of MR Fluid Composition on Properties at Low Strain Ranges

Anna Fenyk1, Wojciech Horak2, Marek Zieliński1

  • 1Department of Inorganic and Analytical Chemistry, Faculty of Chemistry, University of Lodz, Tamka 12, 91-403 Lodz, Poland.

Materials (Basel, Switzerland)
|September 9, 2023
PubMed

Keywords:
DMAcarbonyl ironmagnetic fieldmagnetitemagnetorheological fluidsrheology

More Related Videos

Quantifying Mixing using Magnetic Resonance Imaging07:33

Quantifying Mixing using Magnetic Resonance Imaging

Published on: January 25, 2012

11.0K
Combining Microfluidics and Microrheology to Determine Rheological Properties of Soft Matter during Repeated Phase Transitions11:38

Combining Microfluidics and Microrheology to Determine Rheological Properties of Soft Matter during Repeated Phase Transitions

Published on: April 19, 2018

8.0K

Related Concept Videos

Plastic Behavior01:21

Plastic Behavior

A material's elastic behavior is characterized by the disappearance of stress once the load is removed, allowing the material to return to its original state. However, when stress surpasses the yield point, yielding commences, marking the onset of plastic deformation or permanent set. This change from elastic to plastic behavior is influenced by the peak stress value and the duration before the load is removed. An intriguing observation occurs when a specimen is loaded, unloaded, and...
219
Stress-Strain Diagram - Ductile Materials01:24

Stress-Strain Diagram - Ductile Materials

The stress-strain relationship in ductile materials such as structural steel or aluminium is intricate and progresses through several stages. When a specimen is loaded, it initially exhibits a linear length increase, depicted by a steep straight line on the stress-strain diagram. It indicates the material is elastically deforming and will return to its original shape once unloaded. However, when a critical stress value is reached, plastic deformation begins. This stage sees substantial...
821
Types of Fluids01:27

Types of Fluids

Fluids can be classified into Newtonian and non-Newtonian fluids based on their response to shear stress. Newtonian fluids have a linear relationship between shear stress and the shear strain rate, following Newton's law of viscosity. Their viscosity remains constant regardless of the shear rate, making their behavior predictable and easier to analyze. Common examples include water, air, oil, and gasoline.
In contrast, non-Newtonian fluids do not follow Newton's law of viscosity, and...
315
Hooke's Law01:26

Hooke's Law

Hooke's law, a pivotal principle in material science, establishes that the strain a material undergoes is directly proportional to the applied stress, defined by a factor called the modulus of elasticity or Young's modulus.
465
Mohr's Circle for Plane Strain01:18

Mohr's Circle for Plane Strain

Mohr's circle is a crucial graphical method used to analyze plane strain by plotting strain on a set of cartesian coordinates, where the abscissa is normal strain ∈ and the ordinate is shear strain γ. Similarly to Mohr’s circle for plane stress, two points X and Y are plotted. Their coordinates are (∈x, -γXY) and (∈Y, γXY), respectively.
Mohr's circle visually represents the strain states under various conditions, which is essential for...
558
Strain and Elastic Modulus01:15

Strain and Elastic Modulus

The quantity that describes the deformation of a body under stress is known as strain. Strain is given as a fractional change in either length, volume, or geometry under tensile, volume (also known as bulk), or shear stress, respectively, and is a dimensionless quantity. The strain experienced by a body under tensile or compressive stress is called tensile or compressive strain, respectively. In contrast, the strain experienced under bulk stress and shear stress is known as volume and shear...
3.7K