Related Experiment Video

Updated: Jul 15, 2025

Simulation of Human-induced Vibrations Based on the Characterized In-field Pedestrian Behavior
10:52

Simulation of Human-induced Vibrations Based on the Characterized In-field Pedestrian Behavior

Published on: April 13, 2016

8.8K

Mixed reality drills of indoor earthquake safety considering seismic damage of nonstructural components

Zhen Xu1, Yajun Yang2, Yian Zhu2

  • 1Research Institute of Urbanization and Urban Safety, School of Civil and Resource Engineering, University of Science and Technology Beijing, Beijing, 100083, China. xuzhen@ustb.edu.cn.

Scientific Reports
|September 30, 2023
PubMed

More Related Videos

Mixed Reality for Education MRE Implementation and Results in Online Classes for Engineering04:12

Mixed Reality for Education MRE Implementation and Results in Online Classes for Engineering

Published on: June 23, 2023

683
Data Acquisition Protocol for Determining Embedded Sensitivity Functions07:46

Data Acquisition Protocol for Determining Embedded Sensitivity Functions

Published on: April 20, 2016

6.2K

Related Concept Videos

Types of Building Separation Joints01:23

Types of Building Separation Joints

Building separation joints divide large or complex building structures into smaller, discrete units that can move independently. These joints are categorized into three types: volume-change joints, settlement joints, and seismic separation joints.
Volume-change joints address the effects of expansion and contraction due to temperature and moisture variations. They are strategically placed at discontinuities in a building's mass where cracking is most likely and are spaced about 150 to 200...
250
Dynamic Modulus of Elasticity of Concrete01:16

Dynamic Modulus of Elasticity of Concrete

The dynamic modulus of elasticity assesses how a concrete structure deforms under impact or dynamic loads. It is typically higher than the static modulus of elasticity, measured under slow, steady loading conditions.
The sonic test is a common method to determine the dynamic modulus. In this test, a concrete beam, sized either 6 x 6 x 30 inches or 4 x 4 x 20 inches, is clamped at its center. Vibrations are initiated at one end of the beam by an electromagnetic exciter unit powered by...
374
Reinforced Brick Masonry01:15

Reinforced Brick Masonry

Reinforced brick masonry is an advanced construction technique that enhances the structural integrity of brick walls by incorporating steel reinforcements. These reinforcements are either placed within the hollow cores of bricks or sandwiched between two layers of masonry, known as wythes, and are then secured in place with grout. Grout is a fluid mixture composed of Portland cement, aggregate, and water, providing the necessary bonding agent for the steel and brick.
To fortify brick walls...
1.1K
Masonry Loadbearing Walls01:16

Masonry Loadbearing Walls

Masonry load-bearing walls, constructed from materials like brick, stone, or concrete masonry units, serve as a crucial component in building structures by supporting the loads from floors and roofs and transferring them to the foundation. These walls, known for their compressive strength, can be reinforced or unreinforced to suit different building needs, accommodating both the dead and live loads while maintaining safety through lower working stresses compared to the materials' ultimate...
137
Expansion and Contraction in Masonry Walls01:19

Expansion and Contraction in Masonry Walls

Masonry walls are subject to slight expansion and contraction due to variations in temperature and moisture. Thermal movement in masonry is relatively straightforward to measure and plan for. On the other hand, moisture movement poses more of a challenge. New clay masonry units typically absorb water and expand over time under normal environmental conditions. Conversely, new concrete masonry units tend to shrink as they lose the excess moisture acquired during their production process.
To...
973
Elastic Collisions: Case Study01:15

Elastic Collisions: Case Study

Elastic collision of a system demands conservation of both momentum and kinetic energy. To solve problems involving one-dimensional elastic collisions between two objects, the equations for conservation of momentum and conservation of internal kinetic energy can be used. For the two objects, the sum of momentum before the collision equals the total momentum after the collision. An elastic collision conserves internal kinetic energy, and so the sum of kinetic energies before the collision equals...
14.2K