Related Experiment Video

Updated: Jul 14, 2025

Force System with Vertical V-Bends: A 3D In Vitro Assessment of Elastic and Rigid Rectangular Archwires
08:46

Force System with Vertical V-Bends: A 3D In Vitro Assessment of Elastic and Rigid Rectangular Archwires

Published on: July 24, 2018

10.7K

Dynamic torque and screw-in force of four different glide path instruments assessed in simulated single- and

Myint Thu1, Arata Ebihara1, Keiichiro Maki1

  • 1Department of Pulp Biology and Endodontics, Division of Oral Health Sciences, Graduate School of Medical and Dental Sciences, Tokyo Medical and Dental University (TMDU), Tokyo, Japan.

Journal of Dental Sciences
|October 6, 2023
PubMed
Abstract

Keywords:
Canal configurationGlide pathNickel-titanium instrumentScrew-in forceTorque

More Related Videos

Atomic Force Microscopy Cantilever-Based Nanoindentation: Mechanical Property Measurements at the Nanoscale in Air and Fluid08:58

Atomic Force Microscopy Cantilever-Based Nanoindentation: Mechanical Property Measurements at the Nanoscale in Air and Fluid

Published on: December 2, 2022

3.1K
Dynamic Navigation for Dental Implant Placement05:42

Dynamic Navigation for Dental Implant Placement

Published on: September 13, 2022

3.8K

Related Concept Videos

Deformation in a Circular Shaft01:10

Deformation in a Circular Shaft

One of the distinctive characteristics of circular shafts is their ability to maintain their cross-sectional integrity under torsion. In other words, each cross-section continues to exist as a flat, unaltered entity, simply rotating like a solid, rigid slab. To understand the distribution of shearing stress within such a shaft, consider a cylindrical section inside this circular shaft. This section has a length of L and a radius of R, with one end fixed. The radius of the cylindrical section is...
306
Hydrostatic Pressure Force on a Curved Surface01:04

Hydrostatic Pressure Force on a Curved Surface

Hydrostatic pressure on curved surfaces is a fundamental concept in fluid mechanics with broad applications in the civil engineering field. When fluid is in contact with a curved surface, as in a reservoir, dam, or storage tank, it exerts pressure that varies in magnitude and direction along the curved surface. To assess the total hydrostatic force exerted by the fluid on a curved structure, engineers typically isolate the fluid volume adjacent to the surface and analyze the forces acting on...
1.9K
Torsional Pendulum01:09

Torsional Pendulum

A torsional pendulum involves the oscillation of a rigid body in which the restoring force is provided by the torsion in the string from which the rigid body is suspended. Ideally, the string should be massless; practically, its mass is much smaller than the rigid body's mass and is neglected.
As long as the rigid body's angular displacement is small, its oscillation can be modeled as a linear angular oscillation. The amplitude of the oscillation is an angle. The role of mass is played...
5.6K
Circular Shaft - Stresses in Linear Range01:13

Circular Shaft - Stresses in Linear Range

Consider a scenario where a circular shaft is subject to torque that remains within the boundaries of Hooke's Law, avoiding any permanent deformation. So, the formula for shearing strain is revisited. This formula is multiplied by the modulus of rigidity, and then Hooke's Law for the shearing stress and strain is applied. As a result, the equation for shearing stress in a shaft can be derived.
255
Plastic Deformation in Circular Shafts01:20

Plastic Deformation in Circular Shafts

When materials are subjected to forces that surpass their yield strength, they undergo a process known as plastic deformation. This results in a permanent alteration or strain in their structure. This concept can be specifically applied to circular shafts, where the deformation leads to a change in its shape. The precise evaluation of this plastic deformation requires understanding the stress distribution within the circular shaft, which is achieved by calculating the maximum shearing stress in...
193
Thin-Walled Hollow Shafts01:15

Thin-Walled Hollow Shafts

In analyzing a thin-walled hollow shaft subjected to torsional loading, a segment with width dx is isolated for examination. Despite its equilibrium state, this segment faces torsional shearing forces at its ends. These forces are quantitatively described by the product of the longitudinal shearing stress on the segment's minor surface and the area of this surface, leading to the concept of shear flow. This shear flow is consistent throughout the structure, indicating a uniform distribution...
198