Related Experiment Video

Updated: Jul 14, 2025

Fabricating van der Waals Heterostructures with Precise Rotational Alignment
09:25

Fabricating van der Waals Heterostructures with Precise Rotational Alignment

Published on: July 5, 2019

9.5K

Symmetry Engineering in Twisted Bilayer WTe2

Yijin Zhang1, Keisuke Kamiya1, Takato Yamamoto2

  • 1Institute of Industrial Science, The University of Tokyo, 4-6-1 Komaba, Meguro-ku, Tokyo 153-8505, Japan.

Nano Letters
|October 9, 2023
PubMed

Keywords:
WTe2angle-resolved photoemission spectroscopysymmetry engineeringtwisted van der Waals assembly

More Related Videos

Optimized Fabrication Procedure for High-Quality Graphene-based Moiré Superlattice Devices11:24

Optimized Fabrication Procedure for High-Quality Graphene-based Moiré Superlattice Devices

Published on: July 11, 2025

11
Visualizing Uniaxial-strain Manipulation of Antiferromagnetic Domains in Fe1+YTe Using a Spin-polarized Scanning Tunneling Microscope09:06

Visualizing Uniaxial-strain Manipulation of Antiferromagnetic Domains in Fe1+YTe Using a Spin-polarized Scanning Tunneling Microscope

Published on: March 24, 2019

8.1K

Related Concept Videos

Torsion of Noncircular Members01:16

Torsion of Noncircular Members

Circular shafts undergoing torsional stress maintain their cross-sectional integrity due to their axisymmetric nature. This symmetry ensures an even distribution of stress, allowing the shaft to withstand torsion without distorting. In contrast, square bars, lacking this axial symmetry, experience significant distortion across their cross-sections when subjected to torsion, with the exception of along their diagonals and at lines connecting midpoints. A detailed examination of a cubic element...
146
Symmetric Member in Bending01:07

Symmetric Member in Bending

In the study of the mechanics of materials, analyzing the behavior of prismatic members under opposing couples is crucial for understanding internal stress distributions, which are essential for structural design. When subjected to couples, a prismatic member experiences internal forces that maintain equilibrium. A couple, characterized by two equal and opposite forces, creates a moment but no resultant force. The internal forces at any section cut of the member must balance these external...
176
Unsymmetric Loading of Thin-Walled Members01:23

Unsymmetric Loading of Thin-Walled Members

Thin-walled members with non-symmetrical cross-sections are vital to engineering structures, offering material efficiency and structural integrity. However, unsymmetrical loading on these members leads to complex stress distributions, resulting in simultaneous bending and twisting can cause deformation or structural failure. The interaction between bending and twisting requires detailed analysis to ensure structural resilience.
The concept of the shear center is crucial in countering the...
128
Unsymmetric Bending01:18

Unsymmetric Bending

Unsymmetrical bending occurs when the bending moment applied to a structural member does not align with its principal axis. This misalignment leads to complex stress distributions and deflection patterns that differ from those in symmetrical bending, and are essential for designing structures to withstand different loading conditions. In unsymmetrical bending, the neutral axis—where stress is zero—does not necessarily align with the geometric axes of the cross-section. The...
347
The Y-to-Y Circuit01:19

The Y-to-Y Circuit

In a balanced four-wire wye-to-wye system, the arrangement involves wye-connected sinusoidal voltage sources and loads, connected through a neutral wire that links the neutral nodes of the source and load. The load impedance is connected across each phase of the load. The wye-connected source can be connected to the wye-connected load in four-wire and three-wire arrangements. A three-phase system is considered balanced when the load on each phase is equal, leading to uniform current flow and...
430
Unsymmetric Bending - Angle of Neutral Axis01:15

Unsymmetric Bending - Angle of Neutral Axis

Unsymmetrical bending occurs when a structural member is subjected to bending moments in a plane that does not align with the member's principal axes. This scenario typically arises in beams and other structural components when loads are applied at non-ideal angles, introducing complexities in stress analysis.
When a bending moment is applied at an angle θ concerning the vertical axis of a symmetrical member, it can be resolved into components along the member's principal...
321