Related Experiment Video

Updated: Jul 12, 2025

Simulation, Fabrication and Characterization of THz Metamaterial Absorbers
13:44

Simulation, Fabrication and Characterization of THz Metamaterial Absorbers

Published on: December 27, 2012

15.4K

Terahertz narrowband filter metasurfaces based on bound states in the continuum

Yin Liu, Qiankun Zhang, Xiaohua Xing

    Optics Express
    |October 20, 2023
    PubMed

    More Related Videos

    Terahertz Microfluidic Sensing Using a Parallel-plate Waveguide Sensor07:28

    Terahertz Microfluidic Sensing Using a Parallel-plate Waveguide Sensor

    Published on: August 30, 2012

    10.8K
    Fabricating Metamaterials Using the Fiber Drawing Method11:57

    Fabricating Metamaterials Using the Fiber Drawing Method

    Published on: October 18, 2012

    13.8K

    Related Concept Videos

    Bandpass Sampling01:17

    Bandpass Sampling

    In signal processing, bandpass sampling is an effective technique for sampling signals that have most of their energy concentrated within a narrow frequency band. This type of signal is known as a bandpass signal. The key principle of bandpass sampling involves sampling the signal at a rate that is greater than twice the signal's bandwidth to prevent aliasing.
    A bandpass signal has a spectrum with a lower frequency limit, denoted as ω1, and an upper frequency limit, denoted as ω2....
    188
    Passive Filters01:27

    Passive Filters

    Passive filters are utilized to shape the frequency spectrum of signals across a diverse array of applications. These filters, using only passive elements like resistors (R), inductors (L), and capacitors (C), are capable of selectively allowing or blocking certain frequency ranges without the need for external power sources.
    Low-Pass Filters
    Low-pass filters are designed to transmit signals with frequencies lower than the cutoff frequency, ωc, and attenuate those above it. The cutoff...
    545
    Active Filters01:25

    Active Filters

    Active filters are electronic circuits that use operational amplifiers (op-amps), resistors, and capacitors to filter out unwanted frequency components from a signal. A first-order low-pass active filter is designed to pass signals with a frequency lower than a certain cutoff frequency and attenuate frequencies higher than that cutoff frequency. The transfer function for a first-order low-pass active filter is:
    837
    ¹³C NMR: ¹H–¹³C Decoupling01:04

    ¹³C NMR: ¹H–¹³C Decoupling

    The probability of having two carbon-13 atoms next to each other is negligible because of the low natural abundance of carbon-13. Consequently, peak splitting due to carbon-carbon spin-spin coupling is not observed in spectra. However, protons up to three sigma bonds away split the carbon signal according to the n+1 rule, resulting in complicated spectra.
    A broadband decoupling technique is used to simplify these complex, sometimes overlapping, signals. Broadband decoupling relies on a...
    1.1K
    IR Spectrum Peak Broadening: Hydrogen Bonding01:23

    IR Spectrum Peak Broadening: Hydrogen Bonding

    The vibrational frequency of a bond is directly proportional to its bond strength. As a result, stronger bonds vibrate at higher frequencies, while weaker bonds vibrate at lower frequencies. The stretching vibration of the strong O–H bond in alcohols and phenols (very dilute solution or gas phase) appears as a sharp peak at 3600–3650 cm−1.
    However, the extent of hydrogen bonding influences the observed stretching frequency and band broadening. Intermolecular or intramolecular...
    1.0K
    Parallel Resonance01:23

    Parallel Resonance

    The parallel RLC circuit is an arrangement where the resistor (R), inductor (L), and capacitor (C) are all connected to the same nodes and, as a result, share the same voltage across them. The parallel RLC circuit is analyzed in terms of admittance (Y), which reflects the ease with which current can flow. The admittance is given by:
    213