Related Experiment Video

Updated: Jul 11, 2025

Design and Characterization Methodology for Efficient Wide Range Tunable MEMS Filters
15:25

Design and Characterization Methodology for Efficient Wide Range Tunable MEMS Filters

Published on: February 4, 2018

6.2K

A Frequency-Selective Reconfigurable Antenna for Wireless Applications in the S and C Bands

Alexandros Sakkas1, Vasilis Oikonomou1, Giorgos Mystridis1

  • 1Electronics-Telecommunications and Applications Laboratory, Physics Department, University of Ioannina, 451 10 Ioannina, Greece.

Sensors (Basel, Switzerland)
|November 14, 2023
PubMed

Keywords:
PIN diodemeasurementsmultifrequencypatch antennareconfigurable antenna

More Related Videos

High-speed Continuous-wave Stimulated Brillouin Scattering Spectrometer for Material Analysis07:55

High-speed Continuous-wave Stimulated Brillouin Scattering Spectrometer for Material Analysis

Published on: September 22, 2017

10.2K
Recombination Dynamics in Thin-film Photovoltaic Materials via Time-resolved Microwave Conductivity11:30

Recombination Dynamics in Thin-film Photovoltaic Materials via Time-resolved Microwave Conductivity

Published on: March 6, 2017

11.7K

Related Concept Videos

Characteristics of Series Resonant Circuit01:24

Characteristics of Series Resonant Circuit

Series resonance occurs in a circuit containing inductive (L), capacitive (C), and resistive (R) elements connected sequentially. At the resonance frequency, the inductive and capacitive reactances are equal in magnitude but opposite in sign, effectively canceling each other. This causes the circuit's impedance is minimal, primarily determined by the resistance R. The resonant frequency of an RLC circuit is defined as:
259
Design Example01:23

Design Example

The innovation of touch-tone telephony revolutionized the telecommunications industry by replacing the traditional rotary dial with a dual-tone multi-frequency (DTMF) signaling system. This system uses a matrix-style keypad with buttons arranged in four rows and three columns, creating 12 distinct signals each assigned to a pair of frequencies. Each button press results in a simultaneous generation of two sinusoidal tones – one from a low-frequency group (697 to 941 Hz) and one from a...
332
Parallel Resonance01:23

Parallel Resonance

The parallel RLC circuit is an arrangement where the resistor (R), inductor (L), and capacitor (C) are all connected to the same nodes and, as a result, share the same voltage across them. The parallel RLC circuit is analyzed in terms of admittance (Y), which reflects the ease with which current can flow. The admittance is given by:
213
Conservative Site-specific Recombination and Phase Variation02:53

Conservative Site-specific Recombination and Phase Variation

Because the DNA segments are cut and reorganized in a direction-specific manner, site-specific recombination has emerged as an efficient genetic engineering technique. Flippase and Cyclization recombinases or Flp and Cre, respectively, are two members of the tyrosine recombinase family derived from bacteriophages, that are used to mediate site-specific DNA insertions, deletions, and targeted expression of proteins in mammalian cell lines.
The recognition sites for Cre recombinase called LoxP...
6.0K
Active Filters01:25

Active Filters

Active filters are electronic circuits that use operational amplifiers (op-amps), resistors, and capacitors to filter out unwanted frequency components from a signal. A first-order low-pass active filter is designed to pass signals with a frequency lower than a certain cutoff frequency and attenuate frequencies higher than that cutoff frequency. The transfer function for a first-order low-pass active filter is:
832
Passive Filters01:27

Passive Filters

Passive filters are utilized to shape the frequency spectrum of signals across a diverse array of applications. These filters, using only passive elements like resistors (R), inductors (L), and capacitors (C), are capable of selectively allowing or blocking certain frequency ranges without the need for external power sources.
Low-Pass Filters
Low-pass filters are designed to transmit signals with frequencies lower than the cutoff frequency, ωc, and attenuate those above it. The cutoff...
545