Related Experiment Video

Updated: Jul 8, 2025

Microfluidic Platform with Multiplexed Electronic Detection for Spatial Tracking of Particles
11:54

Microfluidic Platform with Multiplexed Electronic Detection for Spatial Tracking of Particles

Published on: March 13, 2017

9.3K

A 60Mb/s -64dBm Body Channel Communication Transceiver Utilizing Manchester Code

Xuedi Wang, Pengpeng Chen, Cheng Han

    Annual International Conference of the IEEE Engineering in Medicine and Biology Society. IEEE Engineering in Medicine and Biology Society. Annual International Conference
    |December 12, 2023
    PubMed

    More Related Videos

    Data Communication Based on MQTT in a Polymer Extrusion Process08:15

    Data Communication Based on MQTT in a Polymer Extrusion Process

    Published on: July 15, 2022

    3.5K
    Continuous-Wave Propagation Channel-Sounding Measurement System - Testing, Verification, and Measurements09:36

    Continuous-Wave Propagation Channel-Sounding Measurement System - Testing, Verification, and Measurements

    Published on: June 25, 2021

    3.1K

    Related Concept Videos

    Pilot and Numeric Relaying01:21

    Pilot and Numeric Relaying

    Pilot relaying is a type of differential protection used in power systems. It compares electrical quantities at the terminals of equipment via a communication channel instead of direct relay interconnection. This method is essential for transmission lines where the terminals are far apart, typically up to 80 km for lines with 69 to 115 kV ratings. Four types of communication channels are used for pilot relaying:
    86
    Directional Relays01:25

    Directional Relays

    Directional relays, essential for managing unidirectional fault currents, enhance the safety and efficiency of power systems. On power lines equipped with directional relays, faults downstream (to the right) of the current transformer typically cause the fault current to lag the bus voltage by approximately 90 degrees, known as the forward direction. In contrast, upstream (left-side) faults may result in the fault current leading the bus voltage by nearly 90 degrees, termed the reverse...
    118
    Differential Relays01:20

    Differential Relays

    Differential relays are used to protect generators, buses, and transformers by comparing electrical quantities at different points. When a fault occurs, the difference in current between the two points triggers the relay to operate, opening the circuit breaker. Under normal conditions, the current entering (i1) and leaving (i2) a generator are equal. When a fault occurs, however, these currents become unequal, and the difference current flows in the relay operating coil, causing the relay to...
    142
    Clamper Circuit01:14

    Clamper Circuit

    A clamper circuit, also known as a DC restorer, represents a specialized variant of the rectifier circuit, notable for its method of taking the output across the diode rather than the capacitor. This configuration lends to several distinctive applications, particularly in handling square wave inputs.
    Within this circuit, the diode's orientation prompts the capacitor to charge up to the level of the most negative peak of the input signal. Upon reaching this state, the diode ceases to...
    433
    Clipper Circuit01:18

    Clipper Circuit

    A clipper circuit is a fundamental wave-shaping device that harnesses the unique properties of diodes to alter and control waveform characteristics. This technology is widely used in electronic devices, especially in television and radar communication systems, where it enhances waveform modulation in both transmitters and receivers.
    The operation of a clipper circuit can be exemplified by analyzing a dual-clipper configuration setup that integrates two ideal diodes, each paired with a biasing...
    451
    Bipolar Junction Transistor01:22

    Bipolar Junction Transistor

    Bipolar Junction Transistors (BJTs) are essential elements in electronic circuits, playing a crucial role in the functionality of amplifiers, memories, and microprocessors. These transistors can be designed as NPN or PNP based on their doping patterns. They consist of three layers: the emitter, base, and collector. The configuration of these layers and their respective doping levels—with N-type or P-type impurities—define the transistor's type and its operational...
    774