Related Experiment Video

Updated: Jul 5, 2025

Cooling an Optically Trapped Ultracold Fermi Gas by Periodical Driving
11:21

Cooling an Optically Trapped Ultracold Fermi Gas by Periodical Driving

Published on: March 30, 2017

7.5K

Unusual ergodic and chaotic properties of trapped hard rods

Debarshee Bagchi1, Jitendra Kethepalli1, Vir B Bulchandani2,3

  • 1International Centre for Theoretical Sciences, Tata Institute of Fundamental Research, Bengaluru 560089, India.

Physical Review. E
|January 20, 2024
PubMed

More Related Videos

Experimental Methods for Trapping Ions Using Microfabricated Surface Ion Traps11:45

Experimental Methods for Trapping Ions Using Microfabricated Surface Ion Traps

Published on: August 17, 2017

14.4K
Construction and Operation of a Light-driven Gold Nanorod Rotary Motor System09:48

Construction and Operation of a Light-driven Gold Nanorod Rotary Motor System

Published on: June 30, 2018

8.9K

Related Concept Videos

Atomic Nuclei: Nuclear Relaxation Processes01:23

Atomic Nuclei: Nuclear Relaxation Processes

In the absence of an external magnetic field, nuclear spin states are degenerate and randomly oriented. When a magnetic field is applied, the spins begin to precess and orient themselves along (lower energy) or against (higher energy) the direction of the field. At equilibrium, a slight excess population of spins exists in the lower energy state. Because the direction of the magnetic field is fixed as the z-axis,  the precessing magnetic moments are randomly oriented around the z-axis.
655
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
149
Strain-Energy Density01:20

Strain-Energy Density

Understanding the strain energy density in materials under axial load is crucial for evaluating their mechanical behavior and durability. When a rod is subjected to such a load, it elongates and stores energy, known as strain energy, as potential energy within the material. This energy is measured in terms of energy per unit volume.
In the elastic region of a material, the relationship between the stress and the strain is linear and follows Hooke's Law. The strain energy density in this...
415
Stability of structures01:14

Stability of structures

In mechanical engineering, the stability of systems under various forces is critical for designing durable and efficient structures. One fundamental way to explore these concepts is by analyzing systems like two rods connected at a pivot point, O, with a torsional spring of spring constant k at the pivot point. This system is similar in appearance to a scissor jack used to change tires on a car. In this case, the arms of the linkage (equivalent to the rods in this system) are entirely vertical,...
168
Static Equilibrium - II01:07

Static Equilibrium - II

Static equilibrium is a special case in mechanics that is very important in everyday life. It occurs when the net force and the net torque on an object or system are both zero. This means that both the linear and angular accelerations are zero. Thus, the object is at rest, or its center of mass is moving at a constant velocity. However, this does not mean that no forces are acting on the object within the system. In fact, there are very few scenarios on Earth in which no forces are acting upon...
8.5K
Forced Oscillations01:06

Forced Oscillations

When an oscillator is forced with a periodic driving force, the motion may seem chaotic. The motions of such oscillators are known as transients. After the transients die out, the oscillator reaches a steady state, where the motion is periodic, and the displacement is determined.
6.6K