Related Experiment Video

Updated: Aug 8, 2026

Constructing a Collagen Hydrogel for the Delivery of Stem Cell-loaded Chitosan Microspheres
09:39

Constructing a Collagen Hydrogel for the Delivery of Stem Cell-loaded Chitosan Microspheres

Published on: June 1, 2012

16.8K

Chin reinforcement using the hyaluronic acid injectable filler VYC-20L and VYC-25L

Ghada Farouk Mohammed1, Mohammed Saleh Al-Dhubaibi2, Saleh Salem Bahaj3

  • 1Department of Dermatology, Venereology, and Sexology, Faculty of Medicine, Suez Canal University, Ismailia, Egypt.

Journal of Cosmetic Dermatology
|March 19, 2024
PubMed
Abstract

Keywords:
VYC 20LVYC 25Lchinhyaluronic acid

More Related Videos

Preparation of Chitosan-based Injectable Hydrogels and Its Application in 3D Cell Culture08:05

Preparation of Chitosan-based Injectable Hydrogels and Its Application in 3D Cell Culture

Published on: September 29, 2017

19.2K
Clinical Protocol of Producing Adipose Tissue-Derived Stromal Vascular Fraction for Potential Cartilage Regeneration14:49

Clinical Protocol of Producing Adipose Tissue-Derived Stromal Vascular Fraction for Potential Cartilage Regeneration

Published on: September 29, 2018

42.0K

Related Concept Videos

Titration Calculations: Strong Acid - Strong Base02:28

Titration Calculations: Strong Acid - Strong Base

Calculating pH for Titration Solutions: Strong Acid/Strong Base
A titration is carried out for 25.00 mL of 0.100 M HCl (strong acid) with 0.100 M of a strong base NaOH. The pH at different volumes of added base solution can be calculated as follows:
(a) Titrant volume = 0 mL. The solution pH is due to the acid ionization of HCl. Because this is a strong acid, the ionization is complete and the hydronium ion molarity is 0.100 M. The pH of the solution is then:
Titration of a Weak Base with a Strong Acid01:20

Titration of a Weak Base with a Strong Acid

The titration curve of a weak base like ammonia with a strong acid like hydrochloric acid is the mirror image of the titration curve of a weak acid with a strong base.
Using the ICE table and substituting the Kb value, we calculate the initial pH of 50 mL of 0.1 M ammonia to be 11.11. Addition of 25 mL of 0.1 M hydrochloric acid to this solution of ammonia results in a buffer with an equal concentration of ammonia and ammonium ions. The pH of this buffer can be calculated by substituting these...
Titration of Polyprotic Base with a Strong Acid01:18

Titration of Polyprotic Base with a Strong Acid

The titration of a polyprotic base such as sodium carbonate with a strong acid such as hydrochloric acid results in two equivalence points on the titration curve. At the first equivalence point, the carbonate ions in the base are completely converted to bicarbonate ions. The second equivalence point corresponds to the complete conversion of bicarbonate ions to carbonic acid, which dissociates into carbon dioxide and water. The region before the first equivalence point corresponds to the...
Additives and Fillers in Concrete01:29

Additives and Fillers in Concrete

Additives and fillers are integral to enhancing the properties of concrete. Pozzolans and blast-furnace slag are additives or admixtures due to their reactions with calcium hydroxide released during cement hydration. Fillers, which are finely ground and similar in fineness to Portland cement, improve concrete attributes such as workability density, and reduce capillary bleeding or cracking. Some fillers possess hydraulic properties or participate in benign reactions within the cement paste.
The...
Titration of a Strong Acid with a Strong Base01:23

Titration of a Strong Acid with a Strong Base

During the titration of a strong acid with a strong base, pH calculations are primarily based on the concentration of residual hydronium or hydroxide ions. Initially, a strong acid like hydrochloric acid fully dissociates, creating hydronium and chloride ions, resulting in a low pH. The addition of a strong base like sodium hydroxide alters the concentration of hydronium ions by neutralizing them. As more base is added, the pH gradually increases. At the equivalence point, all hydronium ions...
Titration of a Weak Acid with a Strong Base01:30

Titration of a Weak Acid with a Strong Base

In titrating a weak acid with a strong base, different calculation methods are applied at various stages. Initially, the pH of a weak acid like acetic acid is calculated using its dissociation constant (Ka) and an ICE table. Upon addition of a strong base such as sodium hydroxide, a buffer forms, and its pH is determined using the Henderson-Hasselbalch equation. As more base is added and the titration reaches the halfway point, the pH becomes equal to the pKa of the acid, indicating equal...