Related Experiment Video

Updated: Jun 29, 2025

Shaping the Amplitude and Phase of Laser Beams by Using a Phase-only Spatial Light Modulator
08:39

Shaping the Amplitude and Phase of Laser Beams by Using a Phase-only Spatial Light Modulator

Published on: January 28, 2019

9.8K

Transmission mode transformation of rotating controllable beams induced by the cross phase

Zhuoyue Sun, Jie Li, Rui Bian

    Optics Express
    |April 4, 2024
    PubMed

    More Related Videos

    The Generation of Higher-order Laguerre-Gauss Optical Beams for High-precision Interferometry12:14

    The Generation of Higher-order Laguerre-Gauss Optical Beams for High-precision Interferometry

    Published on: August 12, 2013

    21.8K
    Transmission of Multiple Signals through an Optical Fiber Using Wavefront Shaping09:43

    Transmission of Multiple Signals through an Optical Fiber Using Wavefront Shaping

    Published on: March 20, 2017

    9.9K

    Related Concept Videos

    Generation of Three-Phase Voltage01:21

    Generation of Three-Phase Voltage

    A three-phase AC generator has a rotor with a rotating magnet placed within the stator mounted with the stationary three-phase winding to generate three-phase voltages via mutual induction. These windings are evenly distributed around the inner circumference of the stator and are arranged 120 electrical degrees apart. Three-phase stator windings consist of three separate coils or groups of coils, known as phases, each connected in Y (star) configuration or Delta configuration.
    As the rotor...
    375
    Transmission Shafts: Problem Solving01:09

    Transmission Shafts: Problem Solving

    Designing a solid shaft that transmits power from a motor to a machine tool involves a series of calculations to ensure the shaft can withstand the stresses applied by bending moments and torques. First, calculate the torque exerted on the gear, considering the power transmitted by the shaft and its rotational speed. Following this, compute the tangential forces acting on the gears, which directly relate to the torque and the gear radius.
    Next, use bending moment diagrams for the shaft to...
    229
    Angle of Twist: Problem Solving01:13

    Angle of Twist: Problem Solving

    An electric motor applies a torque of 700 N·m to an aluminum shaft, triggering a stable rotation. Two pulleys, B and C, are subjected to torques of 300 N·m and 400 N·m, respectively. The modulus of rigidity is provided as 25 GPa. With the knowledge of the length and diameter of each segment, the twist angle between the two pulleys can be computed. First, a section cut is made between pulleys B and C, and the cut cross-section is analyzed using a free-body diagram. Given that the...
    273
    Design of Transmission Shafts01:16

    Design of Transmission Shafts

    The design of a transmission shaft is governed by two primary specifications: the power it transmits and its rotational speed. These parameters guide the selection of the shaft's material and cross-sectional dimensions, ensuring that the material's maximum shearing stress remains within the elastic limit while transmitting the desired power at the given speed. The system's power is intrinsically linked to the applied torque. The torque applied to the shaft can be calculated by...
    296
    Beams with Symmetric Loadings01:15

    Beams with Symmetric Loadings

    The moment-area method is an analytical tool used in structural engineering to determine the slope and deflection of beams under various loads. Consider a cantilever with a concentrated load and moment at the free end. The first step is constructing a free-body diagram to calculate the reactions at the fixed end. Next, the bending moment diagram is plotted to visualize how the bending moment varies along the beam's length, focusing on points where the bending moment equals zero.
    The M/EI...
    187
    Time and frequency -Domain Interpretation of Phase-lead Control01:24

    Time and frequency -Domain Interpretation of Phase-lead Control

    Phase-lead controllers are commonly used in various control systems to enhance response speed and stability. Adjusting the brightness on a television screen offers a practical example of phase-lead control. When contrast is enhanced, a phase-lead controller is employed. Mathematically, phase-lead control is identified when the first parameter is smaller than the second.
    The design of phase-lead control involves the strategic placement of poles and zeros to balance steady-state error and system...
    83