Related Experiment Video

Updated: Jun 28, 2025

Scanning Electron Microscopic Evaluation of Surface Defects of Remover Retreatment File After Single and Multiple Uses
03:07

Scanning Electron Microscopic Evaluation of Surface Defects of Remover Retreatment File After Single and Multiple Uses

Published on: October 11, 2024

493

Retreatability of NeoSEALER Flo obturated with warm vertical compaction versus single-cone technique using two

Toka Kamaleldeen Elzanaty1, Mohamed M Elashiry2,3, Abeer Hashem Mahran3

  • 1Department of Endodontics, Faculty of Dentistry, Assiut University, Assiut, Egypt.

Journal of Conservative Dentistry and Endodontics
|April 18, 2024
PubMed
Abstract

Keywords:
Calcium silicateremaining debrisretreatmentsingle conewarm vertical compaction

More Related Videos

Reservoir Condition Pore-scale Imaging of Multiple Fluid Phases Using X-ray Microtomography08:02

Reservoir Condition Pore-scale Imaging of Multiple Fluid Phases Using X-ray Microtomography

Published on: February 25, 2015

12.6K
Sandy Soil Improvement through Microbially Induced Calcite Precipitation MICP by Immersion06:27

Sandy Soil Improvement through Microbially Induced Calcite Precipitation MICP by Immersion

Published on: September 12, 2019

9.4K

Related Concept Videos

Placing Concrete01:17

Placing Concrete

The concrete is placed as close as possible to its final position to avoid segregation. The placed concrete is then fully compacted to expel the entrapped air, and the next layer of concrete is laid while the underlying layer is still in the plastic state. The rate at which concrete is placed and compacted is kept equal.
While placing concrete, care is taken to ensure that the concrete is laid in uniform layers, and hand shoveling and moving concrete using poker vibrators is avoided. Also,...
96
Preplaced Aggregate Concrete01:29

Preplaced Aggregate Concrete

Preplaced aggregate concrete is ideal for construction environments that are not easily accessible. The process begins by properly wetting the gap-graded coarse aggregates to remove the dirt, then placing it in the form and compacting it. Voids are filled with a mortar mix pumped under pressure through slotted pipes. This mortar typically consists of Portland cement, pozzolan, fine aggregates, water, and a fluidizing aid. The pozzolan helps reduce bleeding and segregation while improving the...
95
Design Example: Managing Concrete Workability01:14

Design Example: Managing Concrete Workability

This example deals with managing the workability of concrete for a raft foundation project under hot weather conditions. Workability is crucial for ensuring the concrete is easy to place, compact, and finish. In this scenario, a slump test — a common method to measure the workability of fresh concrete — initially indicated low workability. This was attributed to the rapid water loss from the concrete mix, exacerbated by the high temperatures causing the course aggregates to heat up.
80
Porosity in Cement Paste01:18

Porosity in Cement Paste

The porosity of concrete is a measure of the void spaces within its structure. These spaces impact its strength and durability significantly. When water and cement interact, a chemical reaction called hydration creates a semi-solid paste. This paste includes combined water, making up approximately 23% of the cement's dry mass, and gel water, which fills minuscule voids known as gel pores, accounting for about 28% of the cement gel volume.
The balance of water to cement in the mix is...
127
Shotcrete01:18

Shotcrete

Shotcrete is a specialized technique where mortar or small aggregate concrete rich in cement content is sprayed onto a surface at high velocity. The force of impact compacts the material and enables it to cling to vertical or overhead areas without sagging. The technique involves layering the shotcrete in stages until it reaches approximately 4 inches in thickness. Operator skill in nozzle management is pivotal in deciding the quality of the shotcrete. Shotcrete is used in constructing tunnel...
59
Slump Test01:20

Slump Test

The slump test is a widely used method to measure the workability of concrete. It employs a 12-inch high truncated cone mold that tapers from eight inches at the base to four inches at the top. Before testing, the mold is securely attached to a flat base and dampened.
Concrete is poured into the mold in three layers to conduct the test. Each layer is compacted 25 times with a steel tamping rod, which has a five-eighths-inch diameter and a rounded end, to ensure even distribution and eliminate...
214