Related Experiment Video

Updated: Jun 25, 2026

High Speed Droplet-based Delivery System for Passive Pumping in Microfluidic Devices
10:22

High Speed Droplet-based Delivery System for Passive Pumping in Microfluidic Devices

Published on: September 2, 2009

13.8K

Simple Method for On-Demand Droplet Trapping in a Microfluidic Device Based on the Concept of Hydrodynamic Resistance

Mohsen Besanjideh1,2, Masoud Rezaeian1,2, Amir Shamloo1,2

  • 1Department of Mechanical Engineering, Sharif University of Technology, Tehran 11365-11155, Iran.

Langmuir : the ACS Journal of Surfaces and Colloids
|April 23, 2024
PubMed

More Related Videos

A Microfluidic-based Hydrodynamic Trap for Single Particles10:13

A Microfluidic-based Hydrodynamic Trap for Single Particles

Published on: January 21, 2011

16.7K
Capillary-based Centrifugal Microfluidic Device for Size-controllable Formation of Monodisperse Microdroplets08:20

Capillary-based Centrifugal Microfluidic Device for Size-controllable Formation of Monodisperse Microdroplets

Published on: February 22, 2016

10.4K

Related Concept Videos

Fluid Pressure01:14

Fluid Pressure

In mechanical engineering, fluid pressure plays a critical role in designing systems that utilize liquid flow, such as hydraulic systems, pumps, and valves. When designing these systems, engineers must ensure they can withstand the forces created by fluid pressure to avoid damage or failure.
According to Pascal's law, a fluid at rest will generate equal pressure in all directions. This pressure is measured as a force per unit area, and its magnitude depends on the fluid's specific weight or...
Bernoulli's Principle: Applications01:17

Bernoulli's Principle: Applications

There are many devices and situations in which fluid flows at a constant height and so can be analyzed using Bernoulli's principle. These devices include, but are not limited to, entrainment devices and fluid flow measuring devices.
Entrainment devices use a high fluid speed to create low pressures and, thus, entrain one fluid into another. Some examples of these devices are given below:
Surface Tension of Fluid01:22

Surface Tension of Fluid

Surface tension is a fundamental property of fluids, occurring at the boundary between a liquid and a gas or between two immiscible liquids. This phenomenon arises from the cohesive forces between molecules at the fluid's surface, creating an effect similar to a stretched elastic membrane. Inside each fluid, molecules are equally attracted in all directions by neighboring molecules, but surface molecules experience a net inward force, resulting in surface tension.
Surface tension varies with...
Application of the Linear Momentum Equation01:15

Application of the Linear Momentum Equation

The application of the linear momentum equation can be used to analyze the forces needed to hold a 180-degree pipe bend in place with flowing water. In this case, water flows through the bend with a constant cross-sectional area of 0.01 square meters and a flow velocity of 15 meters per second. The pressure at the entrance is 0.2 Megapascals and the pressure at the exit is 0.16 Megapascals.
The goal is to determine the force components in the x and y directions to hold the pipe in place. Since...
Design Example: Forces in Sluice Gate01:11

Design Example: Forces in Sluice Gate

In hydraulic engineering, sluice gates are essential for managing water flow through channels, reservoirs, and irrigation systems. Sluice gates, acting as vertical barriers, regulate water by adjusting the gate's opening height, which changes the velocity and pressure of water flowing beneath the gate. Understanding the forces involved is crucial to designing sluice gates that can withstand dynamic pressure differences, especially when the gate is closed or partially open.
Key variables in...
Pipe Flowrate Measurement: Problem Solving01:28

Pipe Flowrate Measurement: Problem Solving

A spray tank system is engineered to uniformly distribute a pest-control liquid across plants by using a pressurized mechanism. The tank, pressurized to 150 kPa, holds the pesticide at a height of 0.80 meters. Liquid flows from the tank through a 1.9 meter pipe with a diameter of 0.015 meters, angled at 0.698 radians, ultimately reaching a 0.007 meter nozzle that sprays the pesticide. Accurate calculation of the system's flow rate is crucial to ensure uniform application, and this is achieved...