Related Experiment Video

Updated: Jun 25, 2025

Effect of Bending on the Electrical Characteristics of Flexible Organic Single Crystal-based Field-effect Transistors
08:43

Effect of Bending on the Electrical Characteristics of Flexible Organic Single Crystal-based Field-effect Transistors

Published on: November 7, 2016

8.0K

Photo- and Stress-Induced Bending of (E)-1,2-Bis(pyridinium-4-yl)ethene Dinitrate Crystals

Sotaro Kusumoto1, Kaede Wakabayashi1, Kenta Rakumitsu2

  • 1Department of Applied Chemistry, Faculty of Chemistry and Biochemistry, Kanagawa University, 3-27-1 Rokkakubashi, Kanagawa-ku, Yokohama, 221-8686, Japan.

Chemistry (Weinheim an Der Bergstrasse, Germany)
|May 26, 2024
PubMed

Keywords:
Elastic crystalPhoto-actuationPhoto-induced bending

More Related Videos

Novel Techniques for Observing Structural Dynamics of Photoresponsive Liquid Crystals10:35

Novel Techniques for Observing Structural Dynamics of Photoresponsive Liquid Crystals

Published on: May 29, 2018

8.7K
High-Contrast and Fast Photorheological Switching of a Twist-Bend Nematic Liquid Crystal06:24

High-Contrast and Fast Photorheological Switching of a Twist-Bend Nematic Liquid Crystal

Published on: October 31, 2019

6.4K

Related Concept Videos

Members Made of Elastoplastic Material01:19

Members Made of Elastoplastic Material

The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
As the bending moment...
95
Residual Stresses in Bending01:18

Residual Stresses in Bending

In the study of elastoplastic members subjected to bending moments, understanding the loading and unloading phases is crucial for assessing material behavior and structural integrity. During the loading phase, as the bending moment increases, the material initially responds elastically, adhering to Hooke's Law, where stress is directly proportional to strain. When the load exceeds the yield strength, plastic deformation occurs, resulting in permanent strain and deformation that remains even...
160
Plastic Behavior01:21

Plastic Behavior

A material's elastic behavior is characterized by the disappearance of stress once the load is removed, allowing the material to return to its original state. However, when stress surpasses the yield point, yielding commences, marking the onset of plastic deformation or permanent set. This change from elastic to plastic behavior is influenced by the peak stress value and the duration before the load is removed. An intriguing observation occurs when a specimen is loaded, unloaded, and...
196
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
86
Conformations of Cycloalkanes02:29

Conformations of Cycloalkanes

Adolf von Baeyer attempted to explain the instabilities of small and large cycloalkane rings using the concept of angle strain — the strain caused by the deviation of bond angles from the ideal 109.5° tetrahedral value for sp3  hybridized carbons. However, while cyclopropane and cyclobutane are strained, as expected from their highly compressed bond angles, cyclopentane is more strained than predicted, and cyclohexane is virtually strain-free. Hence, Baeyer’s theory that...
11.8K
Deformations in a Symmetric Member in Bending01:18

Deformations in a Symmetric Member in Bending

When analyzing the deformation of a symmetric prismatic member subjected to bending by equal and opposite couples, it becomes clear that as the member bends, the originally straight lines on its wider faces curve into circular arcs, with a constant radius centered at a point known as Point C. This phenomenon helps to understand the stress and strain distribution within the member more clearly.
When the member is segmented into tiny cubic elements, it is observed that the primary stress...
166