Related Experiment Video

Updated: Jun 24, 2025

Microfluidic Fabrication Techniques for High-Pressure Testing of Microscale Supercritical CO2 Foam Transport in Fractured Unconventional Reservoirs
10:06

Microfluidic Fabrication Techniques for High-Pressure Testing of Microscale Supercritical CO2 Foam Transport in Fractured Unconventional Reservoirs

Published on: July 2, 2020

6.8K

Impact Pressure Characteristics of Carbon Dioxide Phase Transition Fracturing Technique

Bingzhen Yu1, Shuaishuai Niu1, Shengtao Zhou1

  • 1Faculty of Engineering, China University of Geosciences, Wuhan 430074, China.

ACS Omega
|June 10, 2024
PubMed

More Related Videos

A Uniaxial Compression Experiment with CO2-Bearing Coal Using a Visualized and Constant-Volume Gas-Solid Coupling Test System10:27

A Uniaxial Compression Experiment with CO2-Bearing Coal Using a Visualized and Constant-Volume Gas-Solid Coupling Test System

Published on: June 12, 2019

8.7K
Reservoir Condition Pore-scale Imaging of Multiple Fluid Phases Using X-ray Microtomography08:02

Reservoir Condition Pore-scale Imaging of Multiple Fluid Phases Using X-ray Microtomography

Published on: February 25, 2015

12.6K

Related Concept Videos

Phase Diagrams02:39

Phase Diagrams

A phase diagram combines plots of pressure versus temperature for the liquid-gas, solid-liquid, and solid-gas phase-transition equilibria of a substance. These diagrams indicate the physical states that exist under specific conditions of pressure and temperature and also provide the pressure dependence of the phase-transition temperatures (melting points, sublimation points, boiling points). Regions or areas labeled solid, liquid, and gas represent single phases, while lines or curves represent...
40.5K
Phase Diagram01:19

Phase Diagram

The phase of a given substance depends on the pressure and temperature. Thus, plots of pressure versus temperature showing the phase in each region provide considerable insights into the thermal properties of substances. Such plots are known as phase diagrams. For instance, in the phase diagram for water (Figure 1), the solid curve boundaries between the phases indicate phase transitions (i.e., temperatures and pressures at which the phases coexist).
5.8K
Carbonation Shrinkage01:24

Carbonation Shrinkage

Atmospheric CO2 penetrates the concrete's pores and, in the presence of moisture, forms carbonic acid, which then reacts with calcium hydroxide in the hydrated cement, forming calcium carbonate. This process reduces the concrete's volume and is termed carbonation shrinkage.
The concrete's permeability is slightly reduced as calcium carbonate produced during the reaction fills its pores. Furthermore, its strength is slightly enhanced as the water released during the reaction...
128
Turbulent Flow: Problem Solving01:09

Turbulent Flow: Problem Solving

Carbonation is a process used to dissolve carbon dioxide gas in a liquid, commonly used in the production of carbonated beverages. Achieving efficient carbonation requires careful control of temperature, pressure, and flow conditions. By adjusting these parameters, carbonation efficiency can be maximized, producing a higher concentration of CO2 in the liquid.
Temperature is a key factor in CO2 solubility. In this case, the CO2 gas and the liquid are cooled to 20°C. Lower temperatures...
113
States of Matter and Phase Changes00:59

States of Matter and Phase Changes

The internal energy of a substance—the total kinetic energy of all its molecules and the potential energy of their associated forces—depends on the strength of the intermolecular forces in the condensed phases and the pressure exerted on the substance. The internal energy of a substance is the highest in the gaseous state, the lowest in the solid state, and intermediate in the liquid state. Phase transitions are caused by changes in physical conditions, such as temperature and...
941
pV-Diagrams01:18

pV-Diagrams

The pV diagram, which is a graph of pressure versus volume of the gas under study, is helpful in describing certain aspects of the substance. When the substance behaves like an ideal gas, the ideal gas equation describes the relationship between its pressure and volume. On a pV diagram, it is common to plot an isotherm, which is a curve showing p as a function of V with the number of molecules and the temperature fixed. Then, for an ideal gas, the product of the pressure of the gas and its...
4.1K