Related Experiment Video

Updated: Jun 23, 2025

Pool-Boiling Heat-Transfer Enhancement on Cylindrical Surfaces with Hybrid Wettable Patterns
07:32

Pool-Boiling Heat-Transfer Enhancement on Cylindrical Surfaces with Hybrid Wettable Patterns

Published on: April 10, 2017

9.0K

Mechanical and thermal performances of multistage flexible thermal control device: A case study in cylindrical heat

Min Liu1, Xiaoping Fan1, Junguang Liu2

  • 1Affiliation: School of Automation, Central South University, Changsha, 410083, China.

Heliyon
|June 24, 2024
PubMed

Keywords:
Bionic designFlexible heat pipeParametric studyThermal performance

More Related Videos

Measurements of Local Instantaneous Convective Heat Transfer in a Pipe - Single and Two-phase Flow08:25

Measurements of Local Instantaneous Convective Heat Transfer in a Pipe - Single and Two-phase Flow

Published on: April 30, 2018

7.1K
Uncoupling Coriolis Force and Rotating Buoyancy Effects on Full-Field Heat Transfer Properties of a Rotating Channel10:03

Uncoupling Coriolis Force and Rotating Buoyancy Effects on Full-Field Heat Transfer Properties of a Rotating Channel

Published on: October 5, 2018

8.2K

Related Concept Videos

Multiple Pipe Systems01:21

Multiple Pipe Systems

Multipipe systems consist of complex configurations of interconnected pipes designed to transport fluids efficiently across intricate networks. They are essential in engineering applications requiring precise control over flow distribution, pressure, and head loss. They are categorized into series, parallel, loop, and network configurations, each distinguished by unique flow characteristics and applications.
Series Configuration
In a series configuration, fluid flows sequentially from one pipe...
738
Heat Capacities of an Ideal Gas I01:14

Heat Capacities of an Ideal Gas I

Heat capacity is the ratio of heat absorbed by the substance corresponding to its temperature change. It is also called thermal capacity and the SI unit of heat capacity is J/K. Whereas, specific heat capacity is defined as the amount of heat necessary to change the temperature of 1 kg of a substance by 1 K and is also called massic heat capacity. Its SI unit is J/kg⋅K.
Molar heat capacity quantifies the ratio of the amount of heat added (or removed) to increase (or decrease) the...
2.6K
Single Pipe Systems01:24

Single Pipe Systems

In pipe flow analysis, problems are typically categorized into three types — Type I, Type II, and Type III — based on the known parameters and the desired outcome. Each type of problem addresses specific engineering requirements using fluid properties, pipe characteristics, and operational conditions.
In a Type I problem, fluid properties (density and viscosity), pipe characteristics (including diameter, length, and surface roughness), and the flow rate or average velocity are...
123
Mechanisms of Heat Transfer I01:14

Mechanisms of Heat Transfer I

Just as interesting as the effects of heat transfer on a system are the methods by which the heat transfer occur. Whenever there is a temperature difference, heat transfer occurs. It may occur rapidly, such as through a cooking pan, or slowly, such as through the walls of a picnic ice box. So many processes involve heat transfer that it is hard to imagine a situation where no heat transfer occurs. Yet, every heat transfer takes place by only three methods: conduction, convection, and radiation.
4.2K
The Carnot Cycle01:30

The Carnot Cycle

Converting work to heat is an irreversible process, and the purpose of a heat engine is to reverse the effect partially. Heat engines aim to increase the efficiency of the reversal, that is, maximize the work retrieved from heat. If the efficiency of a heat engine were 100%, it would imply reversing the process completely without introducing any other effect. Thus, it would violate the second law of thermodynamics.
What could be the theoretical limit to the efficiency of a heat engine? The...
2.8K
Thermal expansion and Thermal stress: Problem Solving01:27

Thermal expansion and Thermal stress: Problem Solving

San Francisco's Golden Gate Bridge is exposed to temperatures ranging from -15 °C to 40 °C. At its coldest, the main span of the bridge is 1275 m long. Assuming that the bridge is made entirely of steel, what is the change in its length between these temperatures?
To solve the problem, first, identify the known and unknown quantities. The initial length (L) of the bridge is 1275 m, the coefficient of linear expansion (α) for steel is 12 x 10-6/°C, and the change in...
1.2K