Related Experiment Video

Updated: Jun 22, 2025

Knowledge Based Cloud FE Simulation of Sheet Metal Forming Processes
11:05

Knowledge Based Cloud FE Simulation of Sheet Metal Forming Processes

Published on: December 13, 2016

12.2K

Study on Spline Stress of Separator Plates in a Wet Multi-Plate Clutch

Biao Ma1, Xiaobo Chen1, Changsong Zheng1

  • 1School of Mechanical Engineering, Beijing Institute of Technology, Beijing 100081, China.

Materials (Basel, Switzerland)
|June 27, 2024
PubMed

Keywords:
clutchfractureseparator platespline toothstress distribution

More Related Videos

Conducting Elevated Temperature Normal and Combined Pressure-Shear Plate Impact Experiments Via a Breech-end Sabot Heater System10:52

Conducting Elevated Temperature Normal and Combined Pressure-Shear Plate Impact Experiments Via a Breech-end Sabot Heater System

Published on: August 7, 2018

8.6K
Structural Design and Manufacturing of a Cruiser Class Solar Vehicle14:57

Structural Design and Manufacturing of a Cruiser Class Solar Vehicle

Published on: January 30, 2019

13.8K

Related Concept Videos

Design of Transmission Shafts - Stress Analysis01:15

Design of Transmission Shafts - Stress Analysis

Designing a transmission shaft requires a thorough understanding of the stresses induced by bending moments and torques, especially in systems where power is transferred through gears. These forces create force-couple systems at the centers of the shaft's cross-sections, leading to both transverse and torsional loading. Although shearing stresses from transverse loads are typically smaller than those from torques and are often overlooked, the significant normal stresses from these loads...
341
Stress Concentrations in Circular Shafts01:18

Stress Concentrations in Circular Shafts

Consider the elastic torsion formula, which applies to a circular shaft with a consistent cross-section. This formula assumes that the shaft's ends are loaded with rigid plates firmly attached. However, in many cases, torques are applied to the shaft through mechanisms like flange couplings or gears, which are connected by keys inserted into keyways. This application method modifies the stress distribution near the point of torque application, causing it to deviate from the distributions...
170
Bearing Stress01:22

Bearing Stress

Bearing stress refers to the contact pressure between two separate bodies. To visualize this, imagine a bolt thrust through a plate. The bolt applies a force to the plate, which exerts an equal but opposite force back onto the bolt. This force isn't just a singular entity but a compilation of numerous smaller forces distributed across the contact surface between the bolt and the plate.
Due to the intricacy of these microforces, an average value, known as bearing stress, is often used by...
794
Shearing Stress01:19

Shearing Stress

Shearing stress, denoted by the Greek letter tau (τ), is stress caused by forces acting transversely on an object. These forces create internal ones within the entity in the plane where the external forces are applied. The resultant of these internal forces is the shear in the section.
The average shearing stress can be calculated by dividing the shear by the area of the cross-section.
542
Residual Stresses in Circular Shafts01:10

Residual Stresses in Circular Shafts

In materials that exhibit elastic and plastic behavior, known as elastoplastic materials, residual stresses can accumulate when these materials experience plastic deformation. This deformation arises from either high levels of shearing stress or significant strains. Residual stresses are internal stresses that persist within a material after removing the external force causing deformation. This phenomenon is demonstrated when observing the behavior of a shaft under torque; notably, the...
166
Stresses in a Shaft01:18

Stresses in a Shaft

The shaft PQ is subjected to a twisting force when equal and opposite torques are applied on either side. A section that cuts perpendicular to the shaft's axis at any arbitrary point R is examined to understand this. When the free-body diagram of the QR segment is analyzed, it reveals the shearing forces exerted by the PR portion onto the QR segment as the shaft experiences twisting.
Applying equilibrium conditions to the QR segment establishes that the internal shearing forces within the...
363