Related Experiment Video

Updated: Jun 18, 2025

Advanced Self-Healing Asphalt Reinforced by Graphene Structures: An Atomistic Insight
08:03

Advanced Self-Healing Asphalt Reinforced by Graphene Structures: An Atomistic Insight

Published on: May 31, 2022

4.5K

Determining the Size of Representative Volume Elements for a Two-Dimensional Random Aggregate Numerical Model of

Sheng Liang1,2, Jing Tao2, Xiaoming Zhao2

  • 1School of Civil and Hydraulic Engineering, Huazhong University of Science and Technology, Wuhan 430074, China.

Materials (Basel, Switzerland)
|July 27, 2024
PubMed

Keywords:
asphalt mortargeometric analysisnumerical analysisrepresenting volume elementstwo-dimensional random aggregate model

More Related Videos

Determination of Aggregate Surface Morphology at the Interfacial Transition Zone ITZ08:59

Determination of Aggregate Surface Morphology at the Interfacial Transition Zone ITZ

Published on: December 16, 2019

8.1K
Laboratory Drop Towers for the Experimental Simulation of Dust-aggregate Collisions in the Early Solar System09:44

Laboratory Drop Towers for the Experimental Simulation of Dust-aggregate Collisions in the Early Solar System

Published on: June 5, 2014

12.7K

Related Concept Videos

Unsoundness of Aggregate due to Volume Change01:26

Unsoundness of Aggregate due to Volume Change

Unsoundness in aggregates due to volume changes is primarily caused by the physical alterations aggregates undergo, such as freezing and thawing, thermal changes, and wetting and drying. Unsound aggregates, when subjected to these changes, result in volume change upon disintegration. This, in turn, contributes to the deterioration of concrete, including scaling, pop-outs, and cracking. Particular types of aggregates, such as porous flints, cherts, and those containing clay minerals, are...
104
Toughness and Hardness of Aggregate01:22

Toughness and Hardness of Aggregate

Toughness and hardness are critical properties of aggregate materials used in concrete, particularly on pavement surfaces and industrial flooring subjected to heavy loads. Toughness is defined as the aggregate's resistance to failure by impact and is measured by the aggregate impact value (AIV). For this, the aggregate impact value test is performed, wherein the impact is delivered by a standard hammer, which falls freely under its own weight onto the aggregates. The aggregates fragment in...
252
Maximum Size of Aggregate01:12

Maximum Size of Aggregate

The maximum size of aggregate is defined as the aperture of the sieve retaining 15 percent or more of the particles present in the aggregate sample. The aggregate's maximum size impacts the concrete's water requirement, workability, and strength. Larger aggregates reduce the surface area needing cement paste coverage, which can lower water needs, thereby allowing a decrease in the water-to-cement ratio when the desired workability and richness of the mix are to be maintained, which can...
97
Design Example: Aggregate Gradation01:24

Design Example: Aggregate Gradation

The right type and quality of aggregates are crucial for concrete as they significantly influence its properties, mix proportions, and cost-effectiveness. If different sources are available for sand, the commonly used fine aggregate in concrete, the selection of sand is primarily based on its gradation.
The grading, or particle-size distribution, of sand is determined using sieve analysis, with standard sizes ranging from 150 μm to 10 mm (ASTM No. 100 sieve to 3⁄8 in. sieve). Sand is...
91
Shape and Texture of Coarse Aggregate01:25

Shape and Texture of Coarse Aggregate

Aggregate shape is classified based on the relative sharpness or roundness of the edges and corners. This classification includes categories like rounded, angular, elongated, and flaky, each with specific characteristics. Rounded aggregates, fully shaped by attrition, are typical of river or seashore gravel, while angular aggregates, such as crushed rock, have well-defined edges. Aggregates that are elongated and flaky are less desirable, as they can reduce the workability and strength of...
200
Porosity and Absorption of Aggregate01:20

Porosity and Absorption of Aggregate

Aggregates contain pores of varying sizes; while some are completely enclosed within the particles, others open onto the surface, allowing water to penetrate. The porosity of aggregates is a major factor contributing to the overall porosity of concrete, given that aggregates constitute about three-quarters of concrete's volume.
When all pores in an aggregate are filled with water, the aggregate is considered saturated and surface-dry. If left in dry air, water will evaporate until the...
273