Related Experiment Video

Updated: Jun 18, 2025

Real-Time DC-dynamic Biasing Method for Switching Time Improvement in Severely Underdamped Fringing-field Electrostatic MEMS Actuators
11:44

Real-Time DC-dynamic Biasing Method for Switching Time Improvement in Severely Underdamped Fringing-field Electrostatic MEMS Actuators

Published on: August 15, 2014

10.3K

Novel Stability Criteria of Asynchronously Switched Nonlinear Neutral Time-Delay Systems

Zhichuang Wang, Wei He, Gang Wang

    IEEE Transactions on Cybernetics
    |August 2, 2024
    PubMed

    More Related Videos

    Design and Application of a Fault Detection Method Based on Adaptive Filters and Rotational Speed Estimation for an Electro-Hydrostatic Actuator06:45

    Design and Application of a Fault Detection Method Based on Adaptive Filters and Rotational Speed Estimation for an Electro-Hydrostatic Actuator

    Published on: October 28, 2022

    1.6K
    Bouncing Ball with a Uniformly Varying Velocity in a Metronome Synchronization Task05:04

    Bouncing Ball with a Uniformly Varying Velocity in a Metronome Synchronization Task

    Published on: September 21, 2017

    6.0K

    Related Concept Videos

    BIBO stability of continuous and discrete -time systems01:24

    BIBO stability of continuous and discrete -time systems

    System stability is a fundamental concept in signal processing, often assessed using convolution. For a system to be considered bounded-input bounded-output (BIBO) stable, any bounded input signal must produce a bounded output signal. A bounded input signal is one where the modulus does not exceed a certain constant at any point in time.
    To determine the BIBO stability, the convolution integral is utilized when a bounded continuous-time input is applied to a Linear Time-Invariant (LTI) system....
    379
    Stability01:28

    Stability

    The time response of a linear time-invariant (LTI) system can be divided into transient and steady-state responses. The transient response represents the system's initial reaction to a change in input and diminishes to zero over time. In contrast, the steady-state response is the behavior that persists after the transient effects have faded.
    The stability of an LTI system is determined by the roots of its characteristic equation, known as poles. A system is stable if it produces a bounded...
    99
    Multimachine Stability01:25

    Multimachine Stability

    Multimachine stability analysis is crucial for understanding the dynamics and stability of power systems with multiple synchronous machines. The objective is to solve the swing equations for a network of M machines connected to an N-bus power system.
    In analyzing the system, the nodal equations represent the relationship between bus voltages, machine voltages, and machine currents. The nodal equation is given by:
    150
    Linear time-invariant Systems01:23

    Linear time-invariant Systems

    A system is linear if it displays the characteristics of homogeneity and additivity, together termed the superposition property. This principle is fundamental in all linear systems. Linear time-invariant (LTI) systems include systems with linear elements and constant parameters.
    The input-output behavior of an LTI system can be fully defined by its response to an impulsive excitation at its input. Once this impulse response is known, the system's reaction to any other input can be...
    238
    Classification of Systems-II01:31

    Classification of Systems-II

    Continuous-time systems have continuous input and output signals, with time measured continuously. These systems are generally defined by differential or algebraic equations. For instance, in an RC circuit, the relationship between input and output voltage is expressed through a differential equation derived from Ohm's law and the capacitor relation,
    138
    Transient and Steady-state Response01:24

    Transient and Steady-state Response

    In control systems, test signals are essential for evaluating performance under various conditions. The ramp function is effective for systems undergoing gradual changes, while the step function is suitable for assessing systems facing sudden disturbances. For systems subjected to shock inputs, the impulse function is the most appropriate test signal.
    These test signals are integral in designing control systems to exhibit two key performance aspects: transient response and steady-state...
    169