Related Experiment Video

Updated: Jun 16, 2025

Chemical Analysis of Water-accommodated Fractions of Crude Oil Spills Using TIMS-FT-ICR MS
08:17

Chemical Analysis of Water-accommodated Fractions of Crude Oil Spills Using TIMS-FT-ICR MS

Published on: March 3, 2017

11.1K

Hydrocarbon composition of oils spilt on the Brazilian coast in 2019 and 2022

Antônia M Corrêa1, Felipe F Campos2, Marcus F Tenório3

  • 1Programa de Pós-Graduação em Química, Universidade Federal Fluminense, Niterói, RJ, Brazil.

Marine Pollution Bulletin
|August 15, 2024
PubMed

Keywords:
Analytical validationHydrocarbonsMarine coastal environmentsOil spillPetroleum biomarkers

More Related Videos

Experimental Procedure for Laboratory Studies of In Situ Burning : Flammability and Burning Efficiency of Crude Oil12:34

Experimental Procedure for Laboratory Studies of In Situ Burning : Flammability and Burning Efficiency of Crude Oil

Published on: May 1, 2018

12.4K
Sediment Core Extrusion Method at Millimeter Resolution Using a Calibrated, Threaded-rod06:06

Sediment Core Extrusion Method at Millimeter Resolution Using a Calibrated, Threaded-rod

Published on: August 17, 2016

11.2K

Related Concept Videos

Combustion Energy: A Measure of Stability in Alkanes and Cycloalkanes02:14

Combustion Energy: A Measure of Stability in Alkanes and Cycloalkanes

The low reactivity in alkanes can be attributed to the non-polar nature of C–C and C–H σ bonds. Alkanes, therefore, were  initially termed as “paraffins,” derived from the Latin words: parum, meaning “too little,” and affinis, meaning “affinity.”
Alkanes undergo combustion in the presence of excess oxygen and high-temperature conditions to give carbon dioxide and water. A combustion reaction is the energy source in natural gas, liquified...
6.3K
Bioremediation00:46

Bioremediation

Bioremediation is the use of prokaryotes, fungi, or plants to remove pollutants from the environment. This process has been used to remove harmful toxins in groundwater as a byproduct of agricultural run-off and also to clean up oil spills.
18.2K
Mass Spectrometry: Long-Chain Alkane Fragmentation01:18

Mass Spectrometry: Long-Chain Alkane Fragmentation

The molecular ions of linear alkanes prefer to fragment at the carbon-carbon bond away from the end of the chain since the cleavage of an inner bond creates a stable carbocation and a stable radical. Consequently, the mass signals of linear alkanes feature intense peaks in the middle of the mass-to-charge ratio plot with weaker peaks on either end. The fragmentation of each carbon-carbon bond with the release of a methyl group in each splitting leads to prominent peaks in the mass spectra...
1.6K
Benzene to Phenol via Cumene: Hock Process01:27

Benzene to Phenol via Cumene: Hock Process

The synthesis of phenol from benzene via cumene and cumene hydroperoxide is called the Hock process. First, a Friedel–Crafts alkylation reaction of benzene with propene gives cumene. Then cumene forms cumene hydroperoxide via a radical chain reaction. In the chain initiation step, the benzylic hydrogen is abstracted to give a benzylic radical. In the chain propagation step, the benzylic radical reacts with an oxygen diradical to form a cumene hydroperoxide radical. The cumene...
3.2K
Physical Properties of Alkanes02:33

Physical Properties of Alkanes

Alkanes are nonpolar molecules due to the presence of only carbon and hydrogen atoms. The electronegativity difference between carbon and hydrogen is minimal, and hence alkanes have a zero dipole moment. This leads to the presence of only dispersion forces between the molecules. The strength of dispersion forces is dependent on the surface area of the molecules on which they act. Since the surface area increases with the molecular length for straight-chain alkanes, the dispersion forces also...
10.8K
Porosity and Absorption of Aggregate01:20

Porosity and Absorption of Aggregate

Aggregates contain pores of varying sizes; while some are completely enclosed within the particles, others open onto the surface, allowing water to penetrate. The porosity of aggregates is a major factor contributing to the overall porosity of concrete, given that aggregates constitute about three-quarters of concrete's volume.
When all pores in an aggregate are filled with water, the aggregate is considered saturated and surface-dry. If left in dry air, water will evaporate until the...
271