Related Experiment Video

Updated: Jun 13, 2025

Scattering And Absorption of Light in Planetary Regoliths
11:34

Scattering And Absorption of Light in Planetary Regoliths

Published on: July 1, 2019

10.3K

Impact sculpting of the early martian atmosphere

Oliver Shorttle1,2, Homa Saeidfirozeh3, Paul Brandon Rimmer2,4

  • 1Institute of Astronomy, University of Cambridge, Madingley Road, Cambridge CB3 0HA, UK.

Science Advances
|September 11, 2024
PubMed

More Related Videos

Emission Spectroscopic Boundary Layer Investigation during Ablative Material Testing in Plasmatron09:41

Emission Spectroscopic Boundary Layer Investigation during Ablative Material Testing in Plasmatron

Published on: June 9, 2016

12.4K
Simulation of Early Earth Hydrothermal Chimneys in a Thermal Gradient Environment06:29

Simulation of Early Earth Hydrothermal Chimneys in a Thermal Gradient Environment

Published on: February 27, 2021

3.5K

Related Concept Videos

Adiabatic Processes for an Ideal Gas01:18

Adiabatic Processes for an Ideal Gas

When an ideal gas is compressed adiabatically, that is, without adding heat, work is done on it, and its temperature increases. In an adiabatic expansion, the gas does work, and its temperature drops. Adiabatic compressions actually occur in the cylinders of a car, where the compressions of the gas-air mixture take place so quickly that there is no time for the mixture to exchange heat with its environment. Nevertheless, because work is done on the mixture during the compression, its...
3.0K
Acceleration due to Gravity on Other Planets01:24

Acceleration due to Gravity on Other Planets

The gravitational acceleration of an object near the Earth's surface is called the acceleration due to gravity. It can be measured by conducting simple experiments on Earth. However, such an experiment is impossible to conduct on the surface of other planets.
Astronomical observations are thus used to measure the acceleration due to gravity on other planets. This can be determined by observing the effect of a planet's gravity on objects close to it. The crucial factor that helps in this...
4.2K
Variation of Atmospheric Pressure01:18

Variation of Atmospheric Pressure

Change in atmospheric pressure with height is particularly interesting. The decrease in atmospheric pressure with increasing altitude is due to the decreasing gravitational force per unit area as we move away from the surface of the earth.
Assuming the air temperature is constant at a given altitude and that the ideal gas law of thermodynamics describes the atmosphere to a good approximation, one can find the variation of atmospheric pressure with height.
Let p(y) be the atmospheric pressure at...
2.1K
Phase Transitions: Sublimation and Deposition02:33

Phase Transitions: Sublimation and Deposition

Some solids can transition directly into the gaseous state, bypassing the liquid state, via a process known as sublimation. At room temperature and standard pressure, a piece of dry ice (solid CO2) sublimes, appearing to gradually disappear without ever forming any liquid. Snow and ice sublimate at temperatures below the melting point of water, a slow process that may be accelerated by winds and the reduced atmospheric pressures at high altitudes. When solid iodine is warmed, the solid sublimes...
17.0K
Influence of Earth's Curvature and Atmospheric Refraction on Leveling01:26

Influence of Earth's Curvature and Atmospheric Refraction on Leveling

During leveling, the Earth's curvature and atmospheric refraction introduce deviations in the line of sight from a true horizontal reference. When the line of sight is leveled, it remains perpendicular to the plumb line only at a single point. Beyond this, it deviates due to the Earth’s curvature, represented by the correction C. For a sight distance D, the deviation can be derived using the relationship:This relationship shows that the deviation increases quadratically with distance.
71
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
143