Related Experiment Video

Updated: Jun 12, 2025

Experimental Methods for Investigation of Shape Memory Based Elastocaloric Cooling Processes and Model Validation
11:11

Experimental Methods for Investigation of Shape Memory Based Elastocaloric Cooling Processes and Model Validation

Published on: May 2, 2016

11.0K

Elastocaloric Heat Pump by Twist Induced Periodical Non-Linear Stress for Low Hysteresis and High Carnot Efficiency

Yicheng Xiao1, Guangkai Mei1, Danyang Feng1,2

  • 1State Key Laboratory of Medicinal Chemical Biology, Key Laboratory of Functional Polymer Materials, College of Chemistry, Nankai University, 94 Weijin Road, Tianjin, 300071, China.

Advanced Materials (Deerfield Beach, Fla.)
|September 27, 2024
PubMed

Keywords:
biomimeticelastocaloric heat pumpsmart fiberssolid‐state refrigerationtorsional non‐linear stress

More Related Videos

Asymmetric Thermoelectrochemical Cell for Harvesting Low-grade Heat under Isothermal Operation09:09

Asymmetric Thermoelectrochemical Cell for Harvesting Low-grade Heat under Isothermal Operation

Published on: February 5, 2020

6.9K
A Cost-effective and Reliable Method to Predict Mechanical Stress in Single-use and Standard Pumps07:34

A Cost-effective and Reliable Method to Predict Mechanical Stress in Single-use and Standard Pumps

Published on: August 5, 2015

9.4K

Related Concept Videos

The Carnot Cycle01:30

The Carnot Cycle

Converting work to heat is an irreversible process, and the purpose of a heat engine is to reverse the effect partially. Heat engines aim to increase the efficiency of the reversal, that is, maximize the work retrieved from heat. If the efficiency of a heat engine were 100%, it would imply reversing the process completely without introducing any other effect. Thus, it would violate the second law of thermodynamics.
What could be the theoretical limit to the efficiency of a heat engine? The...
2.8K
Refrigerators and Heat Pumps01:07

Refrigerators and Heat Pumps

Refrigerators or heat pumps are heat engines operating in a reverse direction. For a refrigerator, the focus is on removing heat from a specific area, whereas, for a heat pump, the focus is on dumping heat into one particular area. A refrigerator (or heat pump) absorbs heat Qc from the cold reservoir at Kelvin temperature Tc and discards heat Qh to the hot reservoir at Kelvin temperature Th, while work W is done on the engine’s working substance.
A household refrigerator removes heat from...
2.2K
Heating and Cooling Curves02:44

Heating and Cooling Curves

When a substance—isolated from its environment—is subjected to heat changes, corresponding changes in temperature and phase of the substance is observed; this is graphically represented by heating and cooling curves.
For instance, the addition of heat raises the temperature of a solid; the amount of heat absorbed depends on the heat capacity of the solid (q = mcsolidΔT). According to thermochemistry, the relation between the amount of heat absorbed or released by a substance, q, and its...
22.8K
Angle of Twist: Problem Solving01:13

Angle of Twist: Problem Solving

An electric motor applies a torque of 700 N·m to an aluminum shaft, triggering a stable rotation. Two pulleys, B and C, are subjected to torques of 300 N·m and 400 N·m, respectively. The modulus of rigidity is provided as 25 GPa. With the knowledge of the length and diameter of each segment, the twist angle between the two pulleys can be computed. First, a section cut is made between pulleys B and C, and the cut cross-section is analyzed using a free-body diagram. Given that the...
266
Mechanisms of Heat Transfer II01:20

Mechanisms of Heat Transfer II

In convection, thermal energy is carried by the large-scale flow of matter. Ocean currents and large-scale atmospheric circulation, which result from the buoyancy of warm air and water, transfer hot air from the tropics toward the poles and cold air from the poles toward the tropics. The Earth’s rotation interacts with those flows, causing the observed eastward flow of air in the temperate zones. Convection dominates heat transfer by air, and the amount of available space for the airflow...
3.2K
Residual Stresses in Circular Shafts01:10

Residual Stresses in Circular Shafts

In materials that exhibit elastic and plastic behavior, known as elastoplastic materials, residual stresses can accumulate when these materials experience plastic deformation. This deformation arises from either high levels of shearing stress or significant strains. Residual stresses are internal stresses that persist within a material after removing the external force causing deformation. This phenomenon is demonstrated when observing the behavior of a shaft under torque; notably, the...
165