Related Experiment Video

Updated: Jun 11, 2025

Use of a Linear Accelerator for Conducting In Vitro Radiobiology Experiments
06:08

Use of a Linear Accelerator for Conducting In Vitro Radiobiology Experiments

Published on: May 26, 2019

7.5K

Integrating sheath and radiation-based acceleration using scaling coefficients for tailoring radiation dominant

Harihara Sudhan Kumar1, Masayuki Takahashi1, Yasuhiro Kuramitsu2

  • 1Department of Aerospace Engineering, Tohoku University, 6-6-01 Aramakiazaaoba, Aoba-ku, Sendai, 980-8579, Japan.

Scientific Reports
|September 28, 2024
PubMed

More Related Videos

Application of Passive Head Motion to Generate Defined Accelerations at the Heads of Rodents05:04

Application of Passive Head Motion to Generate Defined Accelerations at the Heads of Rodents

Published on: July 21, 2022

1.7K
Simulation of Human-induced Vibrations Based on the Characterized In-field Pedestrian Behavior10:52

Simulation of Human-induced Vibrations Based on the Characterized In-field Pedestrian Behavior

Published on: April 13, 2016

8.7K

Related Concept Videos

Relative Motion Analysis - Acceleration01:10

Relative Motion Analysis - Acceleration

A slider-crank mechanism converts rotational motion from the crank into linear motion of the slider or vice versa. This mechanism consists of three main parts: the crank, the connecting rod, and the slider. The movement of the slider-crank is an example of general plane motion as the fluctuating angle between the crank and the connecting rod. Consider a segment AB where point A is at the end of the slider and point B is on the diametrically opposite end to point A, on a crack. The variance in...
340
Load along a Single Axis01:29

Load along a Single Axis

In structural engineering, the analysis of beams subjected to varying loads is a critical aspect of understanding the behavior and performance of these structural elements. A common scenario involves a beam subjected to a combination of different load distributions.
Consider a beam of length L subjected to a varying load, which is a combination of parabolic and trapezoidal load distribution along the x-axis. In this case, it is essential to determine the resultant loads, their locations, and...
287
Thin-Walled Hollow Shafts01:15

Thin-Walled Hollow Shafts

In analyzing a thin-walled hollow shaft subjected to torsional loading, a segment with width dx is isolated for examination. Despite its equilibrium state, this segment faces torsional shearing forces at its ends. These forces are quantitatively described by the product of the longitudinal shearing stress on the segment's minor surface and the area of this surface, leading to the concept of shear flow. This shear flow is consistent throughout the structure, indicating a uniform distribution...
171
Relative Motion Analysis using Rotating Axes - Acceleration01:22

Relative Motion Analysis using Rotating Axes - Acceleration

Consider a component AB undergoing a linear motion. Along with a linear motion, point B also rotates around point A. To comprehend this complex movement, position vectors for both points A and B are established using a stationary reference frame. The absolute velocity of point B is determined by adding the absolute velocity of point A, the relative velocity of point B in the rotating frame, and the effects caused by the angular velocity within the rotating frame.
Time differentiation is...
323
Variation in Acceleration due to Gravity near the Earth's Surface01:20

Variation in Acceleration due to Gravity near the Earth's Surface

An object's apparent weight is its weight measured by a spring balance at its location. It is different from its true weight, the force with which the Earth pulls it, because of the Earth's rotation. Mathematically, an object's apparent weight equals its true weight minus the centripetal force that keeps it in a circular motion along with the Earth's surface every 24 hours.
The difference between the true and apparent weights is proportional to the square of the Earth's...
2.4K
Accelerating Fluids01:17

Accelerating Fluids

When a fluid is in constant acceleration, the pressure and buoyant force equations are modified. Suppose a beaker is placed in an elevator accelerating upward with a constant acceleration, a. In the beaker, assume there is a thin cylinder of height h with an infinitesimal cross-sectional area, ΔS.
The motion of the liquid within this infinitesimal cylinder is considered to obtain the pressure difference. Three vertical forces act on this liquid:
1.0K