Related Experiment Video

Updated: Jun 9, 2025

Surrogate Model Development for Digital Experiments in Welding
09:17

Surrogate Model Development for Digital Experiments in Welding

Published on: March 28, 2025

709

Development of a Quality Control System Using Modal Analysis to Evaluate a Multi-Point Projection Welding Process

Maciej Karpiński1,2, Paweł Sokołowski1, Paweł Kustroń1

  • 1Faculty of Mechanical Engineering, Wroclaw University of Science and Technology, Lukasiewicza 5, 50-371 Wroclaw, Poland.

Materials (Basel, Switzerland)
|October 26, 2024
PubMed

Keywords:
FEMmodal analysisquality controlresistance projection weldingspectral analysisweld quality

More Related Videos

Operation of the Collaborative Composite Manufacturing CCM System10:09

Operation of the Collaborative Composite Manufacturing CCM System

Published on: October 1, 2019

6.6K
Knowledge Based Cloud FE Simulation of Sheet Metal Forming Processes11:05

Knowledge Based Cloud FE Simulation of Sheet Metal Forming Processes

Published on: December 13, 2016

12.1K

Related Concept Videos

Design of Prismatic Beams for Bending01:23

Design of Prismatic Beams for Bending

The design of prismatic beams, structural elements with a uniform cross-section, focuses on ensuring safety and structural integrity under load. The design process begins by determining the allowable stress, either from material properties tables, or by dividing the material's ultimate strength by a safety factor. This safety factor is essential for accommodating uncertainties, and varies depending on the material—timber, steel, or concrete—with each having unique strength and...
213
Design of Transmission Shafts - Stress Analysis01:15

Design of Transmission Shafts - Stress Analysis

Designing a transmission shaft requires a thorough understanding of the stresses induced by bending moments and torques, especially in systems where power is transferred through gears. These forces create force-couple systems at the centers of the shaft's cross-sections, leading to both transverse and torsional loading. Although shearing stresses from transverse loads are typically smaller than those from torques and are often overlooked, the significant normal stresses from these loads...
316
Shear and Bending Moment Diagram: Problem Solving01:24

Shear and Bending Moment Diagram: Problem Solving

When analyzing a beam supporting concentrated loads and a distributed load, drawing the shear and bending moment diagrams is essential. These diagrams help understand the internal forces and moments acting on the beam, which is crucial for designing safe and efficient structures. Follow these steps to create the shear and bending moment diagrams:
Draw a Free-Body Diagram: Start by drawing a free-body diagram of the entire beam, including the concentrated loads, distributed load, and reaction...
1.3K
Bending of Curved Members - Strain Analysis01:14

Bending of Curved Members - Strain Analysis

The mechanics of deformation in curved members, such as beams or arches, under bending moments, involve complex responses. When such a member, symmetric about the y-axis and shaped like a segment of a circle centered at point C, is subjected to equal and opposite forces, its curvature and surface lengths change significantly. This alteration results in the shift of the curvature's center from C to C', indicating a tighter curve.
The important part of bending analysis for such a member...
128
Introduction to Statistical Process Control01:15

Introduction to Statistical Process Control

Statistical Process Control (SPC) is a method used to monitor and control quality within processes, particularly in manufacturing and service delivery, by employing statistical methods. SPC aims to distinguish between natural (common cause) variation and variation due to specific changes or events (special cause), allowing for timely improvements and sustained quality. The control chart, a pivotal tool in SPC, visually displays data over time alongside a central line of upper and lower control...
77
Residual Stresses in Circular Shafts01:10

Residual Stresses in Circular Shafts

In materials that exhibit elastic and plastic behavior, known as elastoplastic materials, residual stresses can accumulate when these materials experience plastic deformation. This deformation arises from either high levels of shearing stress or significant strains. Residual stresses are internal stresses that persist within a material after removing the external force causing deformation. This phenomenon is demonstrated when observing the behavior of a shaft under torque; notably, the...
165