Related Experiment Video

Updated: Jun 7, 2025

Design and Use of a Full Flow Sampling System FFS for the Quantification of Methane Emissions
08:18

Design and Use of a Full Flow Sampling System FFS for the Quantification of Methane Emissions

Published on: June 12, 2016

16.7K

Outage-guaranteed transmission for IRS-assisted FSO systems

Baojun Chen, Xiaodong Zhu

    Optics Express
    |November 14, 2024
    PubMed

    More Related Videos

    Continuous-Wave Propagation Channel-Sounding Measurement System - Testing, Verification, and Measurements09:36

    Continuous-Wave Propagation Channel-Sounding Measurement System - Testing, Verification, and Measurements

    Published on: June 25, 2021

    3.0K
    Alphavirus Transducing System: Tools for Visualizing Infection in Mosquito Vectors07:12

    Alphavirus Transducing System: Tools for Visualizing Infection in Mosquito Vectors

    Published on: November 24, 2010

    14.8K

    Related Concept Videos

    Transmission Line Design Considerations01:23

    Transmission Line Design Considerations

    Aluminum has become the material of choice for overhead transmission lines, surpassing copper due to its abundance and cost-effectiveness. The most prevalent type is the aluminum conductor, steel-reinforced (ACSR), which combines aluminum strands around a steel core. Other variants include all-aluminum conductors (AAC), all-aluminum alloy conductors (AAAC), aluminum conductor alloy-reinforced (ACAR), and aluminum-clad steel conductors. Advanced designs, such as aluminum conductors with steel...
    123
    Power System Distribution01:25

    Power System Distribution

    Power system distribution involves delivering electrical energy from power plants to consumers through a network of transmission and distribution systems. The process begins at power plants, where energy from coal, gas, nuclear, water, and wind is converted into electrical energy. These plants use three-phase generators, typically rated between 50 to 1300 MVA, with terminal voltages ranging from a few kV to 20 kV, depending on the size and age of the units.
    The transmission system is designed...
    226
    Power System Three-Phase Short Circuits01:21

    Power System Three-Phase Short Circuits

    Determining the subtransient fault current in a power system involves representing transformers by their leakage reactances, transmission lines by their equivalent series reactances, and synchronous machines as constant voltage sources behind their subtransient reactances. In this analysis, certain elements are excluded, such as winding resistances, series resistances, shunt admittances, delta-Y phase shifts, armature resistance, saturation, saliency, non-rotating impedance loads, and small...
    77
    Load-frequency control01:28

    Load-frequency control

    Load-frequency control (LFC) is vital for maintaining power system stability, ensuring that frequency and power flows remain within acceptable limits during load changes. Turbine-governor control eliminates rotor accelerations and decelerations following load changes. However, a steady-state frequency error persists when the change in the turbine-governor reference setting is zero. In an interconnected power system, each area agrees to export or import a scheduled amount of power through...
    126
    Overcurrent Relays01:26

    Overcurrent Relays

    Overcurrent relays, crucial for circuit protection, are connected to the secondary current of a current transformer. There are two primary types of overcurrent relays: instantaneous and time-delay.
    Instantaneous overcurrent relays activate immediately when the input current exceeds a predetermined value, known as the pickup current, instantly energizing the circuit breaker trip coil. This rapid response is vital for addressing severe faults quickly.
    Time-delay overcurrent relays, on the other...
    70
    Discrete-Time Fourier Series01:20

    Discrete-Time Fourier Series

    The Discrete-Time Fourier Series (DTFS) is a fundamental concept in signal processing, serving as the discrete-time counterpart to the continuous-time Fourier series. It allows for the representation and analysis of discrete-time periodic signals in terms of their frequency components. Unlike its continuous counterpart, which utilizes integrals, the calculation of DTFS expansion coefficients involves summations due to the discrete nature of the signal.
    For a discrete-time periodic signal x[n]...
    227