Related Experiment Video

Updated: Jun 7, 2025

Film Control to Study Contributions of Waves to Droplet Impact Dynamics on Thin Flowing Liquid Films
07:08

Film Control to Study Contributions of Waves to Droplet Impact Dynamics on Thin Flowing Liquid Films

Published on: August 18, 2018

7.4K

Deformation dynamics of an oil droplet into a crescent shape during intermittent motion

Sayaka Otani1, Hiroaki Ito1, Tomonori Nomoto2

  • 1Department of Physics, <a href="https://ror.org/01hjzeq58">Chiba University</a>, Yayoi-cho 1-33, Inage-ku, Chiba 263-8522, Japan.

Physical Review. E
|November 20, 2024
PubMed

More Related Videos

Fast Imaging Technique to Study Drop Impact Dynamics of Non-Newtonian Fluids10:09

Fast Imaging Technique to Study Drop Impact Dynamics of Non-Newtonian Fluids

Published on: March 5, 2014

12.4K
High Throughput Analysis of Liquid Droplet Impacts09:00

High Throughput Analysis of Liquid Droplet Impacts

Published on: March 6, 2020

6.4K

Related Concept Videos

Deformation in a Circular Shaft01:10

Deformation in a Circular Shaft

One of the distinctive characteristics of circular shafts is their ability to maintain their cross-sectional integrity under torsion. In other words, each cross-section continues to exist as a flat, unaltered entity, simply rotating like a solid, rigid slab. To understand the distribution of shearing stress within such a shaft, consider a cylindrical section inside this circular shaft. This section has a length of L and a radius of R, with one end fixed. The radius of the cylindrical section is...
265
Dynamics of Circular Motion01:30

Dynamics of Circular Motion

An object undergoing circular motion, like a race car, is accelerating because it is changing the direction of its velocity. This centrally directed acceleration is called centripetal acceleration. This acceleration acts along the radius of the curved path (thus is also referred to as radial acceleration).
Any acceleration must be produced by some force. Therefore, any force or combination of forces can cause centripetal acceleration. A few examples include the tension in the rope on a...
13.4K
Plastic Deformation in Circular Shafts01:20

Plastic Deformation in Circular Shafts

When materials are subjected to forces that surpass their yield strength, they undergo a process known as plastic deformation. This results in a permanent alteration or strain in their structure. This concept can be specifically applied to circular shafts, where the deformation leads to a change in its shape. The precise evaluation of this plastic deformation requires understanding the stress distribution within the circular shaft, which is achieved by calculating the maximum shearing stress in...
180
Excess Pressure Inside a Drop and a Bubble01:13

Excess Pressure Inside a Drop and a Bubble

The shape of a small drop of liquid can be considered spherical, neglecting the effect of gravity. This drop can further be considered as two equal hemispherical drops put together due to surface tension. The forces acting on the spherical drop are due to the pressure of the liquid inside the drop, the pressure due to air outside the drop, and the force due to the surface tension acting on the two hemispherical drops.
1.6K
Dynamics Of Circular Motion: Applications01:17

Dynamics Of Circular Motion: Applications

Suppose a car moves on flat ground and turns to the left. The centripetal force causing the car to turn in a circular path is due to friction between the tires and the road. For this, a minimum coefficient of friction is needed, or the car will move in a larger-radius curve and leave the roadway. Let's now consider banked curves, where the slope of the road helps in negotiating the curve. The greater the angle of the curve, the faster one can take the curve. It is common for race tracks for...
7.7K
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
140