Related Experiment Video
Updated: Jun 6, 2025
A Simple, Low-cost, and Robust System to Measure the Volume of Hydrogen Evolved by Chemical Reactions with Aqueous Solutions
Published on: August 17, 2016
Hydrogen Production from Formic Acid Using KIT-6 Supported Non-Noble Metal-Based Catalysts
Dilsad Dolunay Eslek Koyuncu1, Ilkin Tug1, Nuray Oktar1
1Chemical Engineering Department, Gazi University, Address 1, 06570, Ankara, Turkey.
Abstract:
The aim of this study is to investigate the activity of KIT-6 supported nickel (Ni) and cobalt (Co) catalysts, and the effect of Co incorporation to the Ni@KIT-6 catalyst in the formic acid (FA) dehydrogenation. Ni and Co are inexpensive and readily available non-noble transition metals that are considered ideal for dehydrogenation reactions due to their high activity against C-C and C-H bond breaking. In this study, KIT-6 supported catalysts were tested for hydrogen production from FA in a conventionally heated packed-bed continuous-flow system. N2 adsorption-desorption isotherms of the samples were found to be consistent with Type-IV according to the International Union of Pure and Applied Chemistry (IUPAC) classification. The introduction of metal loading resulted in the preservation of the mesoporous structure of the support material. X-ray diffraction (XRD) patterns of the catalysts exhibited the characteristic amorphous silica structure. Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFT) analysis, Lewis acidity of Co-based catalysts was found to be higher than the Ni-based catalysts. The complete formic acid conversion was observed at 200-350 °C. The highest H2 selectivity was obtained with the 3Ni@KIT-6 catalyst. The Co-based catalysts exhibited relatively lower catalytic activity, which was linked to increased coke formation within these catalysts.
More Related Videos
08:40Synthesis of Metal Nanoparticles Supported on Carbon Nanotube with Doped Co and N Atoms and its Catalytic Applications in Hydrogen Production
Published on: December 6, 2021
09:18Simple Methods for the Preparation of Non-noble Metal Bulk-electrodes for Electrocatalytic Applications
Published on: June 21, 2017
Related Concept Videos
02:17Reduction of Alkenes: Asymmetric Catalytic Hydrogenation
The metal catalyst used can be either heterogeneous or homogeneous. When hydrogenation of an alkene generates a chiral center, a pair of enantiomeric products is expected to form. However, an enantiomeric excess of one of the products can be facilitated using an enantioselective reaction or an...
02:13Reduction of Alkenes: Catalytic Hydrogenation
Metals like palladium, platinum, and nickel are commonly used in their solid forms — fine powder on an inert surface. As these catalysts remain insoluble in the reaction mixture, they are referred to as heterogeneous catalysts.
The hydrogenation process takes place on the...
02:50Catalysis
02:24Reduction of Alkynes to cis-Alkenes: Catalytic Hydrogenation
Like alkenes, alkynes can be reduced to alkanes in the presence of transition metal catalysts such as Pt, Pd, or Ni. The reaction involves two sequential syn additions of hydrogen via a cis-alkene intermediate.
01:13Esters to Carboxylic Acids: Acid-Catalyzed Hydrolysis
During hydrolysis, the ester is first activated towards nucleophilic attack through the protonation of the carboxyl oxygen atom by the acid catalyst. The protonation makes the ester carbonyl carbon more electrophilic. In the next step, water acts as a nucleophile and adds to the...
01:01Acid Halides to Carboxylic Acids: Hydrolysis
As shown below, the mechanism involves a nucleophilic attack by water at the carbonyl carbon to form a tetrahedral intermediate. This is followed by the reformation of the carbon–oxygen π bond along with the departure of a halide ion. A final proton transfer step yields carboxylic...