Related Experiment Video

Updated: Jun 5, 2025

Evaluation of an Exclusive Spur Dike U-Turn Design with Radar-Collected Data and Simulation
11:41

Evaluation of an Exclusive Spur Dike U-Turn Design with Radar-Collected Data and Simulation

Published on: February 1, 2020

20.3K

Exploring safety effects on urban expressway diverging areas: crash risk estimation considering extreme conflict

Jiaqiang Wen1, Nengchao Lyu1, Lai Zheng2

  • 1Intelligent Transportation Systems Research Center, Wuhan University of Technology, Wuhan, China.

International Journal of Injury Control and Safety Promotion
|December 16, 2024
PubMed

Keywords:
Traffic conflictscooperative modellingextreme value modelsrisk estimationvehicle trajectory

More Related Videos

Evaluating the Effect of Roadside Parking on a Dual-Direction Urban Street14:55

Evaluating the Effect of Roadside Parking on a Dual-Direction Urban Street

Published on: January 20, 2023

3.2K
Using a Virtual Reality Walking Simulator to Investigate Pedestrian Behavior06:38

Using a Virtual Reality Walking Simulator to Investigate Pedestrian Behavior

Published on: June 9, 2020

4.8K

Related Concept Videos

Design Example: Analyzing Capacity Contours for Flood Risk Assessment01:17

Design Example: Analyzing Capacity Contours for Flood Risk Assessment

Flood risk assessment involves careful planning and analysis to ensure the safety of communities near water retention structures. Capacity contours are a vital tool in this process, as they illustrate the potential spread of water at specific levels in a given area. In the context of building a bund across a small valley, these contours play a critical role in evaluating the safety of nearby residential areas.In this example, the bund is intended to store stormwater in the valley. The engineers...
40
Stress Concentrations01:24

Stress Concentrations

Stress concentration is when stress intensifies near discontinuities such as holes or abrupt cross-sectional changes in a structural member. This localized stress can often surpass the average stress within the member. The stress distribution in flat bars, either with a circular hole or varying widths connected by fillets, can be determined experimentally using a photoelastic method. The results are based on ratios of geometric parameters like the ratio of the hole's radius to the smaller...
273
Relative Risk01:12

Relative Risk

Relative risk (RR) is a statistical measure commonly used in epidemiology to compare the likelihood of a particular event occurring between two groups. This metric is important for evaluating the relationship between exposure to a specific risk factor and the probability of a particular outcome. It plays a crucial role in medical research, public health studies, and risk assessment. Relative risk quantifies how much more (or less) likely an event is to occur in an exposed group compared to an...
116
Hazard Ratio01:12

Hazard Ratio

The hazard ratio (HR) is a widely used measure in clinical trials to compare the risk of events, such as death or disease recurrence, between two groups over time. It reflects the ratio of hazard rates—the instantaneous risk of the event occurring—between a treatment group and a control group. This measure provides valuable insights into the relative effectiveness of a treatment by assessing how the risk of an event differs between the two groups.
For example, in a clinical trial...
87
Elevation of Intermediate Points on Vertical Curves01:20

Elevation of Intermediate Points on Vertical Curves

Vertical curves are essential in roadway design because they provide smooth transitions between varying roadway grades. Designing vertical curves involves calculating intermediate elevations and identifying the curve's highest or lowest point, which is essential for optimal roadway performance.Intermediate elevations on a vertical curve are determined using the tangent offset method. This method considers the initial elevation at the start of the curve, the grades, and the curve's geometry. The...
22
Design Consideration01:22

Design Consideration

Designing a structure involves a series of considerations, primarily the material's ultimate strength, calculated through tests that measure changes under increased force until the material reaches its breaking point or limit. The ultimate load, where the material breaks, is divided by its original cross-sectional area, resulting in the ultimate normal stress or strength. The ultimate shearing stress is another significant factor taken into account.
The factor of safety is another key...
180