Related Experiment Video

Updated: Jun 4, 2025

Fabrication and Testing of Microfluidic Optomechanical Oscillators
09:10

Fabrication and Testing of Microfluidic Optomechanical Oscillators

Published on: May 29, 2014

12.1K

Design, Fabrication and Characterization of Disk Resonator Gyroscope with Vibration and Shock Resistance

Zhaoyang Zhai1,2, Xiaorui Bie1, Bingchen Zhu1,2,3

  • 1The State Key Laboratory of Transducer Technology, Aerospace Information Research Institute, Chinese Academy of Sciences, Beijing 100190, China.

Sensors (Basel, Switzerland)
|December 17, 2024
PubMed

Keywords:
disk resonator gyroscopequality factorstructure design

More Related Videos

Fabrication of Silica Ultra High Quality Factor Microresonators07:51

Fabrication of Silica Ultra High Quality Factor Microresonators

Published on: July 2, 2012

16.4K
Fabrication and Characterization of Superconducting Resonators10:26

Fabrication and Characterization of Superconducting Resonators

Published on: May 21, 2016

11.2K

Related Concept Videos

Design Example: Underdamped Parallel RLC Circuit01:17

Design Example: Underdamped Parallel RLC Circuit

Consider designing an oscillator circuit, a crucial component in various electronic devices and systems. The objective is to create an oscillator circuit with specific characteristics: a damped natural frequency of 4 kHz and a damping factor of 4 radians per second. To accomplish this, a parallel RLC circuit is employed, known for its ability to sustain oscillations at a resonant frequency. In this case, the damping factor is pivotal in achieving the desired performance.
Starting with a fixed...
260
Concept of Resonance and its Characteristics01:19

Concept of Resonance and its Characteristics

If a driven oscillator needs to resonate at a specific frequency, then very light damping is required. An example of light damping includes playing piano strings and many other musical instruments. Conversely, to achieve small-amplitude oscillations as in a car's suspension system, heavy damping is required. Heavy damping reduces the amplitude, but the tradeoff is that the system responds at more frequencies. Speed bumps and gravel roads prove that even a car's suspension system is not...
5.0K
Residual Stresses in Circular Shafts01:10

Residual Stresses in Circular Shafts

In materials that exhibit elastic and plastic behavior, known as elastoplastic materials, residual stresses can accumulate when these materials experience plastic deformation. This deformation arises from either high levels of shearing stress or significant strains. Residual stresses are internal stresses that persist within a material after removing the external force causing deformation. This phenomenon is demonstrated when observing the behavior of a shaft under torque; notably, the...
159
Faraday Disk Dynamo01:23

Faraday Disk Dynamo

A Faraday disk dynamo is a DC generator, producing an emf that is constant in time. It consists of a conducting disk that rotates with a constant angular velocity in the magnetic field, perpendicular to the disk's plane. The rotation of the disk causes a change in magnetic flux, which induces an emf, causing opposite charges to develop on the rim and in the center of the disk. The polarity of the induced emf can be determined by the direction of the magnetic field and the direction of the...
2.1K
Magnetic Damping01:17

Magnetic Damping

Eddy currents can produce significant drag on motion, called magnetic damping. For instance, when a metallic pendulum bob swings between the poles of a strong magnet, significant drag acts on the bob as it enters and leaves the field, quickly damping the motion.
If, however, the bob is a slotted metal plate, the magnet produces a much smaller effect. When a slotted metal plate enters the field, an emf is induced by the change in flux; however, it is less effective because the slots limit the...
421
Design Example: Calculating Safe Diameter for Wind-Exposed Disc01:17

Design Example: Calculating Safe Diameter for Wind-Exposed Disc

Assessing safety in wind-exposed installations is crucial to preventing potential failures. This example explores the calculation and design adjustments needed to mount a circular disc on a building facade, where wind forces are a primary concern. A 4-meter diameter disc was initially designed as an aesthetic feature facing winds at a velocity of 25 meters per second, with an air density of 1.25 kilograms per cubic meter. Given these conditions, the drag force on the disc was determined using...
41