Related Experiment Video

Updated: May 8, 2025

A Modeling and Simulation Method for Preliminary Design of an Electro-Variable Displacement Pump
09:04

A Modeling and Simulation Method for Preliminary Design of an Electro-Variable Displacement Pump

Published on: June 1, 2022

2.9K

Application of AVL BOOST modeling to optimize the engine working load and drivetrain transmission ratio of the diesel

Thong Duc Hong1,2, Binh Nhat Nguyen1,2, Phat Tan Truong1,2

  • 1Faculty of Transportation Engineering, Ho Chi Minh City University of Technology (HCMUT), Ho Chi Minh City, Viet Nam.

Heliyon
|December 25, 2024
PubMed

Keywords:
AVL BOOSTBelt driveDrivetrain designEngine performance characteristicsFirefighting pumpTransmission ratio

More Related Videos

A Rapid Method for Modeling a Variable Cycle Engine04:58

A Rapid Method for Modeling a Variable Cycle Engine

Published on: August 13, 2019

7.5K
Modeling and Experimental Analysis of the Single-Shaft Coaxial Motor-Pump Assembly in Electrohydrostatic Actuators08:59

Modeling and Experimental Analysis of the Single-Shaft Coaxial Motor-Pump Assembly in Electrohydrostatic Actuators

Published on: June 13, 2022

2.4K

Related Concept Videos

Design of Transmission Shafts01:16

Design of Transmission Shafts

The design of a transmission shaft is governed by two primary specifications: the power it transmits and its rotational speed. These parameters guide the selection of the shaft's material and cross-sectional dimensions, ensuring that the material's maximum shearing stress remains within the elastic limit while transmitting the desired power at the given speed. The system's power is intrinsically linked to the applied torque. The torque applied to the shaft can be calculated by...
263
Transmission Shafts: Problem Solving01:09

Transmission Shafts: Problem Solving

Designing a solid shaft that transmits power from a motor to a machine tool involves a series of calculations to ensure the shaft can withstand the stresses applied by bending moments and torques. First, calculate the torque exerted on the gear, considering the power transmitted by the shaft and its rotational speed. Following this, compute the tangential forces acting on the gears, which directly relate to the torque and the gear radius.
Next, use bending moment diagrams for the shaft to...
190
Design of Transmission Shafts - Stress Analysis01:15

Design of Transmission Shafts - Stress Analysis

Designing a transmission shaft requires a thorough understanding of the stresses induced by bending moments and torques, especially in systems where power is transferred through gears. These forces create force-couple systems at the centers of the shaft's cross-sections, leading to both transverse and torsional loading. Although shearing stresses from transverse loads are typically smaller than those from torques and are often overlooked, the significant normal stresses from these loads...
275
Internal Combustion Engine01:20

Internal Combustion Engine

The internal combustion engine is a heat engine that uses the byproducts of combustion as the working fluid instead of using a heat transfer medium to transfer heat. The combustion is done in a way that produces high-pressure combustion products that can be expanded through a turbine or piston to create work. Internal combustion engines can again be categorized into three kinds: (1) spark ignition gasoline engines, most commonly used in automobiles, (2) compression ignition diesel engines that...
846
Mechanical Efficiency of Real Machines01:14

Mechanical Efficiency of Real Machines

The mechanical efficiency of a machine is a fundamental concept that describes how effectively a machine can convert input work into output work. According to this concept, the efficiency of a machine is equal to the ratio of the output work to the input work. An ideal machine, meaning a machine that has no energy losses, has an efficiency of one. This implies that the input work and the output work are equal.
However, in reality, no machine can be truly ideal, and all of them experience some...
566
Distributed Loads: Problem Solving01:21

Distributed Loads: Problem Solving

Beams are structural elements commonly employed in engineering applications requiring different load-carrying capacities. The first step in analyzing a beam under a distributed load is to simplify the problem by dividing the load into smaller regions, which allows one to consider each region separately and calculate the magnitude of the equivalent resultant load acting on each portion of the beam. The magnitude of the equivalent resultant load for each region can be determined by calculating...
590