Related Experiment Video

Updated: May 7, 2025

Thermal Scanning Conductometry TSC as a General Method for Studying and Controlling the Phase Behavior of Conductive Physical Gels
10:01

Thermal Scanning Conductometry TSC as a General Method for Studying and Controlling the Phase Behavior of Conductive Physical Gels

Published on: January 23, 2018

7.6K

TCCbuilder: An open-source tool for the analysis of thermal switches, thermal diodes, thermal regulators, and thermal

Katja Vozel1, Katja Klinar1, Nada Petelin1

  • 1Faculty of Mechanical Engineering, University of Ljubljana, Askerceva 6, 1000 Ljubljana, Slovenia.

Iscience
|January 6, 2025
PubMed

Keywords:
Heat transferOpen source softwareThermal engineeringThermal property

More Related Videos

Thermal Measurement Techniques in Analytical Microfluidic Devices08:29

Thermal Measurement Techniques in Analytical Microfluidic Devices

Published on: June 3, 2015

9.6K
Experimental Methodology for Estimation of Local Heat Fluxes and Burning Rates in Steady Laminar Boundary Layer Diffusion Flames10:29

Experimental Methodology for Estimation of Local Heat Fluxes and Burning Rates in Steady Laminar Boundary Layer Diffusion Flames

Published on: June 1, 2016

11.7K

Related Concept Videos

Elements of Block Diagrams01:25

Elements of Block Diagrams

Block diagrams serve as a visual representation of the input-output relationships within a system. An illustrative example is a heating system, where the set temperature activates the furnace to warm the room to the desired level. Block diagrams are versatile, modeling linear systems through Laplace transform variables and nonlinear systems using time domain variables.
A block diagram typically includes essential elements such as comparators, blocks, and feedback loops. Each of these elements...
210
Differential Relays01:20

Differential Relays

Differential relays are used to protect generators, buses, and transformers by comparing electrical quantities at different points. When a fault occurs, the difference in current between the two points triggers the relay to operate, opening the circuit breaker. Under normal conditions, the current entering (i1) and leaving (i2) a generator are equal. When a fault occurs, however, these currents become unequal, and the difference current flows in the relay operating coil, causing the relay to...
78
Switching of BJT01:22

Switching of BJT

Switching behavior in Bipolar Junction Transistors (BJTs) is a fundamental aspect utilized in various electronic circuits, particularly for digital logic applications like switches and amplifiers. In a typical switching circuit, a BJT alternates between cut-off and saturation modes, corresponding to the "off" and "on" states, respectively, thus behaving like an ideal switch.
Cut-off Mode ("Off" State): In this state, both the emitter-base and collector-base junctions are...
344
Non-ohmic Devices00:51

Non-ohmic Devices

In most substances, the current flow is proportional to the voltage applied to it. A simple relationship between the values of current, voltage, and resistance is known as Ohm's law. Nonohmic devices do not exhibit a linear relationship between voltage and current. One such device is the semiconducting circuit element known as a diode. A diode is a circuit device that allows current flow in only one direction.
Consider a simple circuit consisting of a battery, a diode, and a resistor. A...
984
Electric Circuit Elements01:21

Electric Circuit Elements

Circuit elements are the basic building blocks of an electric circuit. Essentially, an electric circuit is the interconnection of these elements. Within electric circuits, one can find two types of elements: passive and active. Active elements have the ability to generate energy, whereas passive elements do not. Passive elements include components like resistors, capacitors, and inductors, while active elements typically encompass generators, batteries, and operational amplifiers.
The most...
569
Calorimetry01:19

Calorimetry

When objects at different temperatures are placed in contact with each other but isolated from everything else, they attain thermal equilibrium. A container that prevents heat transfer in or out is called a calorimeter, and the use of a calorimeter to make measurements is called calorimetry. Generally, these measurements involve heat or specific heat capacity. The term "calorimetry problem" is used for any problem where the specified objects are thermally isolated from their...
2.8K